PORTED LS1 Heads/Comp Custom Grind Cam Made 450WHP 404WTQ FS

[EliteZ]

PORTED LS1 Heads/Comp Custom Grind Cam Made 450WHP 404WTQ
99-00 #853
Casting Number 853 or 241
LS1 (Center Bolt)
99-00 5.7L Passenger Car and Corvette (853)
01+ 5.7L Passenger Car and Corvette (241)
Material: Aluminum
Combustion Chamber Volume: 66.67cc
Intake Port Volume: 200cc
Exhaust Port Volume: 70cc
Intake Valve Diameter: 2.00 inches
Exhaust Valve Diameter: 1.55 inches

Fresh from the machine shop w/ new valve seals.
921 comp valve springs(Properly seated w/ equal spring pressure)
Ferroa 2.02 aftermarket intake valves
Milled to give 11.7:1 compression. (W/ good tune run excellent on pump gas)(Was previously tuned by Jeremy Formato on original owners daily driver 01 TA)

Custom Grind Comp Cam #C7942
236/230 114LSA+2 601/591Lift
(Comes w/ Comp Cams Cam card printout)
2-3K miles on cam.

Bought to install on my 98 LS1, decided to go another route (FI).


Install info from original owners car.
http://www.ls1tech.com/forums/showthread.php?t=221398

Dyno Sheet
http://www.ls1tech.com/forums/attach...chmentid=15130

Info on company who did the install
http://www.pm-fl.com/catalog/results...463fe3437de1d4
Click "Camaro/Firebird 1998-2002 LS and look for

"Ryan's 2001 Firebird 6-Speed -- 450 RWHP / 404 RWTQ
Precision Motorsports Stage 3 Ported, Polished, and Coated LS1 Heads
Stock 346 CID engine
236/230 Cam
Long Tube Headers
Muffler, Lid, and Pulleys "

This was when they were on the original owners vehicle. Since then the heads have been gone through and checked, and double checked. Additional

portwork done, to finish the smoothing of the runners, pocket ported, and the valve pocket has been ported to match the enlarged Ferroa valves.

Pics will be up ASAP, will include Cam Sheet, and my receipt for the headwork, as well as heads/cam.


I am only asking for the money I have in these heads/Cam. Not in a hurry to sell.

$1800.

PM/EMAIL/REPLY for more info.

Located in Central Florida.

Buyer pays shipping.


Thanks for looking,

John.

[1fastcamarosss11]

are you selling all this as one? if not please put price for each item.

[third_shift|studios]

i'm not totally clear what's being sold here, but 1800 for a full package sounds decent...

[juiced99ws6]

Stock LS1 heads
Fresh from the machine shop w/ new valve seals.
921 comp valve springs(Properly seated w/ equal spring pressure)
Ferroa 2.02 aftermarket intake valves
Milled to give 11.7:1 compression. (W/ good tune run excellent on pump gas)(Was previously tuned by Jeremy Formato on original owners daily driver 01 TA)

Custom Grind Comp Cam #C7942
236/230 114LSA+2 601/591Lift
(Comes w/ Comp Cams Cam card printout)
2-3K miles on cam.

these should be the items for sale. everything else is just stats on the stock heads for comparison and then the stats on the car it was previously installed on to give an idea of what you should expect.

[dkamaro]

I already have the long tubes, underdrive pulleys, lid and all other bolt on mods. What would the heads and cam set up installed cost?

[Ridinfilthy]

1500???

[EliteZ]

I replied to some messages, ttt.


1500 shipped to you. (please email/pm your location, etc.)

[EliteZ]

Thanks for clarifying juiced.