**** The "Morning After" Train ****

[GTP231]

Got exhaust on the GTP? They sound pretty nasty with exhaust.

Just some 3" pipe with a resonator and stock mufflers. Its quiet inside and not a pissed off bee hive at wot

[cammed goat]

I'm out. See you all in a few hours. Falling asleep.

[LS1FirehawkWS6]

I'm out. See you all in a few hours. Falling asleep.

I'm out as well ... g'night all

[toi tyme]

Mufflex with a spin tech sounds awesome also.

http://s61.photobucket.com/albums/h4...t=5b862d3b.pbr

http://s61.photobucket.com/albums/h4...t=MVI_0116.flv

Ive seen these before! Is that you and your car?

[01ws6er]

I wanna bring em all the way to the back.. haha

Yeah I may do a custom set up.. But I am SUPER low on cash.. So Ill prob have to wait for summer.

Depending on the tubing used and whether or not it's mandrel bent (mine are not) you could spend anywhere between $600-$2000) My buddy has duals under axle, with an x-pipe, and dynomax bullets (aluminized tubing) and they cost $600.

Stepped down from Bud fat to Busch Light 30 pack

I hear ya it sucks! Moving back in with the parents, which sucks, but I'm gettin a kegerator!

[Hi-Po]

Ive seen these before! Is that you and your car?

Yes

[toi tyme]

I'm out. See you all in a few hours. Falling asleep.

I'm out as well ... g'night all

Nite boys!

[GTP231]

Hey GTP...check this out:
http://www.mpd-inc.net/gp.htm

I know a guy with a real "F1" GTP. I like that hood or the GTX hoods can't decide

[toi tyme]

Yes

hha thats nuts Sounds really yyyy good!

[01ws6er]

I know a guy with a real "F1" GTP. I like that hood or the GTX hoods can't decide

Saw me a red GTX in Conshohocken today. Nice lookin car!

[GTP231]

Same block as the LS2 IIRC

Hope not if you got the long bolts LS2s are all short bolts like the LS6

[01ws6er]

Hope not if you got the long bolts LS2s are all short bolts like the LS6

I have an Ls6 block and my stud kit had long/short studs (and then the really little one's closest to the valley)

[GTP231]

If it is, I work at Caterpillar, The have every damn bolt ever made. All grade 8. I will just drive up there and get one, while laid off

So, GTP... if its not 120mm that I receive with this gasket kit, I should buy one that measures to those specs?

Nevermind was thinking about head bolts.
Doesn't have to be 120mm exactly. I would'nt go to far off that eitherway.

[GTP231]

I have an Ls6 block and my stud kit had long/short studs (and then the really little one's closest to the valley)

Could've sworn they took all short. I forget damn old age

[TONYsHAWK]

hello?

[01ws6er]

Could've sworn they took all short. I forget damn old age

Top ones are tiny, Far middle are short (the 3 in the middle on the middle and bottom row for a total of 6), and then there are 4 long ones (outsides of the middle and bottom). I tried to put a few of the long ones in the middle and wondered why they were all over the place.

[01ws6er]

hello?

[GTP231]

Top ones are tiny, Far middle are short (the 3 in the middle on the middle and bottom row for a total of 6), and then there are 4 long ones (outsides of the middle and bottom). I tried to put a few of the long ones in the middle and wondered why they were all over the place.

Every LS6 I've done was all the shorter bolts. Oh well

[01ws6er]

Every LS6 I've done was all the shorter bolts. Oh well

I'll take pics of the block, but it's an Ls6... This is making me worry since you do this for a living But nah, all the studs ended up being the same height when I got em in the right spots

[toi tyme]

My neck hurts..