What did you do to/with your Camaro today?

[Spikito]

i was trying to get my dash cap to fit and did this.




the blood is only in the wound bed, any fingernail not seen is missing.....when i got back from the ER i found the severed chunk next to the bloody box cutter

[KING Z28 HAWK]

SOB! Ouch! Dam dude that looks painful.

[95cam86roc]

Tires showed yesterday, now I'm just waiting to get my transmission back so I can mate it to the new motor.

[10spokess]

oh god that looks so painful. I just broke my finger the other day changing my friends brakes, but man I am so glad I didn't do that. Wish you a fast recovery

[Spikito]

yeah i just had my wife change the dressing again....the vaseline covered dressing moved so the dry gauze dried in the wound and had scabbed.....thats a whole new level of pain, and they didnt give me any pain meds

[tatertot91]

Ouch!
Must have been cussing like a mofo, i know i would have been

[KING Z28 HAWK]

I'm with you on this one Alex. I actually cussed as soon as I saw it.

[Whitefish]

Did the "ominous glow mod". I was stoked to get finished & check it out, but the LEDs are defective...the last two inches aren't working. Still looks ok, but I already contacted the company to send a replacement.



Sent from my SCH-I800 using Tapatalk

[tatertot91]

Finished molding my dual gauge pillar to find it's an 93-96 style pillar, wont work for me since there isn't a hole for the defrost vent
Pissed me off enough to put an order out for a few new parts, scrapping the pillar idea
Also installed my water temp sender, still have oil pressure sender to do as well as run all my wiring

Did the "ominous glow mod". I was stoked to get finished & check it out, but the LEDs are defective...the last two inches aren't working. Still looks ok, but I already contacted the company to send a replacement.

Did you get pics throughout the install?

[Spikito]

I left it open to air for a little while today, I wanted to see how much is was oozing/bleeding, if it would scab, etc.


Well I was cleaning it up and I could see some of the spots pulsing, kinda freaking

[Whitefish]

Did you get pics throughout the install?

No, really wasn't much to it. I would take finished pics, but the LEDs that are burnt out make it kinda hard to see in a pic. Hardest part was running the wire & it wasn't too bad. You thinking about doing it?



Sent from my SCH-I800 using Tapatalk

[tatertot91]

I've thought about it for my previous camaro but never actually did it.
I might tru it on a spare panel one of these days but i like my stainless inserts

[Whitefish]

I used the stickie in the appearance museum. Hardest part was figuring out how to get the wires through the c-shaped air dam. I took a wire hanger, made a loop out of one end (small loop), ran it through until I saw it in the scoop, grabbed it, taped my wires to it, and pulled it back out. Worked much better than tryingvto snaked the lights through, like it says to do in the stickie. I can snap some pics, as I will have to do it again, since my LEDs were messed up. Only thing I dislike about it, is it kinda ruins that clean look under the hood, since the wires are kinda just there. I might try & get some wire loom to clean it up. Good luck, if you try it....but it really is pretty simple.

Sent from my SCH-I800 using Tapatalk

[Shermanator86]

Magnaflow catback finished up yesterday

[cancam99ss]

Decided to cut the roof on the Camaro to make it a targa top Camaro like the vettes

[BLK2KSS]

Decided to cut the roof on the Camaro to make it a targa top Camaro like the vettes

cant wait to see this! Ive always wished I had a targa instead of t-tops

[Spikito]

so what are you going to do for a roof?

[cancam99ss]

Targa top

[10spokess]

Did you get fiberglass or carbon fiber

[KING Z28 HAWK]

We need pics of this!