problem idling

Printable View

12-17-2009, 04:02 AM
grouch0jr

problem idling

so this morning i started my car, and it died immediately. confused, i tried it again, and gave it a little gas to hold the rpm at around 1000 rmp, and checked all my gauges. everything looked fine (except for the SES light, which ive had for a while, i need an 'crank re-learn procedure' done. im going to check my codes at lunch to see if anything else was thrown). i let off the throttle again, and the engine just died. no funny noises or anything. i did the same thing one more time, except i held the throttle a little long, and it finally idled around 500 rpm.

as the car warmed up it acted more normal. this morning was cold, but not the coldest of the year yet. another thing i noticed was that at idle there seemed t be more fumes (no cats) than usual.

does this indicate a problem with the 02 sensors?
12-17-2009, 08:17 AM
grouch0jr

somebody, anybody?
12-17-2009, 08:27 AM
SOMbitch

Dirty IAC is where I would start but get that code pulled......
12-17-2009, 08:47 AM
grouch0jr

what the hell is IAC? during lunch it started up just fine. this time it idled a little high. i didnt get the codes read because i have a reader at home, gonna do it then.
12-17-2009, 08:49 AM
grouch0jr

ahhhh, idle air control. where is this located?
12-17-2009, 08:58 AM
Spaz

when is the last time you changed yoru fuel filter???
12-17-2009, 09:06 AM
grouch0jr

never.
12-17-2009, 09:08 AM
Hi-Po

IAC

Pink Arrow - IAC
Red Arrow - Throttle postion sensor

http://i61.photobucket.com/albums/h4...o2/IACloca.jpg
12-17-2009, 09:09 AM
luvmyz28

could be a slight vacumme leak as well. my exploder acted like that when it was cold outside. it turned out to be the intake manifold gasket. when it was cold out the gasket would leak. when the engine warmed up the material expanded and sealed it up.
12-17-2009, 09:13 AM
grouch0jr

Quote:

Originally Posted by SOMbitch

Dirty IAC is where I would start but get that code pulled......

Quote:

Originally Posted by Hi-Po

IAC

Pink Arrow - IAC
Red Arrow - Throttle postion sensor

ill check the codes when i get home, then move forward with the trouble shooting.
12-17-2009, 12:24 PM
SOMbitch

Quote:

Originally Posted by grouch0jr

ill check the codes when i get home, then move forward with the trouble shooting.

There is a little motor in the IAC and sometimes the carbon builds up and makes it stick. If this is your problem a good cleaning will fix it. I have never seen one actually go bad so they usually just get dirty.
12-17-2009, 01:05 PM
grouch0jr

Quote:

Originally Posted by SOMbitch

There is a little motor in the IAC and sometimes the carbon builds up and makes it stick. If this is your problem a good cleaning will fix it. I have never seen one actually go bad so they usually just get dirty.

how do you clean it?
12-17-2009, 02:32 PM
grouch0jr

ok, no codes thrown. so does the eliminate the IAC?
12-17-2009, 03:02 PM
Hi-Po

Quote:

Originally Posted by grouch0jr

ok, no codes thrown. so does the eliminate the IAC?

No, my IAC was all jacked up and never set a code.
12-18-2009, 07:04 AM
SOMbitch

Unplug it first. Then take the two torx screws out and the valve comes out in one piece.

Simply spray the hell out of it, everywhere, with MAF cleaner or Sea Foam spray or WD-40.

Then spray inside the port where it goes. Black crap builds up in there and that black rubber piece on the valve leaves a gummy residue in there. You can twist a rag and stick it in there too to get the crud.

Also pull it out real slow to make sure the spring doesn't pull out.