Results 1 to 7 of 7
Thread: 67 Camaro Cam Opinions Wanted
-
06-12-2012, 07:38 PM #1
67 Camaro Cam Opinions Wanted
Hey all, (posted this over on tech too, but I like you guys better )
Don't know much about cams yet. Well, I keep teaching myself over and over, but I still have yet to do any cam work myself so I have a bit of trouble retaining it....
Anyways, my pops had his 350 rebuilt in his 67 camaro ss 350 and they tossed in this cam.
12-670-4 - NOSTALGIA PLUS Hydraulic Flat Tappet Camshafts
Just looking for some feedback on how aggressive this is on a basically stock motor (stock 4 barrel, manifolds, and a pipes x-pipe with magnaflow out back) otherwise. With the rebuild he also switched from a powerglide to a muncie 4-speed and tossing some some 3.73's in the factory 12 bolt.
He and I'd both like a few opinions. To me it sounds Nasty as all get out, at least for my dad, mr. ultra conservative.
Thanks!
oh and since threads are worthless out pics, here's a couple from when he had it over at my house for a few days...
-
06-13-2012, 08:09 AM #2
That camshaft with it's 211/218 at .050 numbers and .420 lift appears to be a middle cam or a mix if you will,,,,of either the factory 327/300hp camshaft and the 327/350hp camshaft.
327/300hp.....112 lsa and intake centerline 112 (no advance)
With .390/.410 lift and duration at .050 of 195/202
327/350hp.....114 las and intake centerline 114 (no advance)
with .447 lift both sides and duration at .050 of 222 both sides
Your camshaft appears to be some newer grind with a mix inbetween
With .426/.420 lift and duration at .050 of 211/218
Ground at a 112 lsa with an intake centerline of 108 so it had 4 degrees of advance ground into the camshaft.
Honestly that's a very tame camshaft that should idle baby butt smooth even with a 112 lsa. The duration numbers are nearly stock (not much more than the old 300hp camshafts used in 327's and 350's of the era). Actually that 300hp camshaft spec I listed would have been the factory camshaft your fathers 350/295hp 67 camaro would have had if it is indeed a real SS350 car. That camshaft you stuck in is basically only slightly bigger and probably wouldn't be all that noticable.
I ran the 350hp camshaft for years in one of my 327's and it had a mild lope. 222 @ .050 duration and the 114 lsa made it a very nice camshaft and a great daily driver for me at the time. Remember that's the little engine that Grumpy reaked havic on in stock eliminator NHRA racing in 1966 beating all the hemis.
In any event, don't know how this camshaft you posted sounds "nasty as all get out" with those specs, it should be rather smooth running. Overall it's a nice camshaft and as I said,,,,is very close to what would have been the factory camshaft in a 67 350/295hp engine at that time.
-
06-13-2012, 09:46 AM #3
- Join Date
- Jun 2007
- Location
- Baltimore, MD.
- Posts
- 728
Bright Red- 2000 Pontiac Trans Am WS6
I agree, that cam shouldn't be "nasty sounding" by any means. I have the 327/350 cam in my 67 and it idles quite calmly. compared to most "cammed" cars. If it's idling rough, I'd have to guess maybe the valve adjustment isn't right, or maybe a vacuum leak. Regardless, it should be more than ok for a car that can be driven everyday without any issues.
Beautiful car by the way. I recently removed the PG transmission out of mine and only wish it could have been replaced b y a stick shift trans...
-
06-13-2012, 10:13 AM #4
-
06-13-2012, 11:31 AM #5
-
06-13-2012, 12:16 PM #6
thanks. The nastiness was due to a Carb issue causing a rough idle he fixed last night. Now it sounds normal and sounds like exactly what he wanted. Real big thanks!
And btw it is a numbers matching 295 HP car
-
06-29-2012, 11:49 AM #7
- Join Date
- Feb 2007
- Location
- San Diego, CA
- Posts
- 5,823
2002 Z28 A4 NBM- Sadly now demodded :(
FBJ is right in that that cam is pretty mild, almost stock AAMOF. I used the 327/350 cam in my last 327 (in yet another 67 I used to have) and it never gave me any problems, pretty peppy even with a TH350 and 3.08 gears
67 Camaro: K-K + 797-z (look it up), 454/Th400/4.10 12-bolt = 6mpg, PS/PDB/PW tilt, tach, gauges...
2005 Corvette LS2/M6 Magnetic Red Metallic (What else would it be?) w/ Cashmere interior
2002 Z28: NBM/Tan, MTI smooth lid, smooth bellows, !AIR, !cats, 1-3/4" QTP SS LT's, 2-1/2" TD's with X-pipe, MagnaFlows dumped at axle, custom welded SFC's, MidWest Chassis body mount adjustable T/A, 3400 stall, 3.23 gears (was 2.73). Tuned: 343rwhp/357rwt (before TD's). Best: 12.559 @ 108+, 1.73 60' @ 3500' DA w/MT ET Street DR's.
Carbon footprint? CLOWN SHOE!
Thread Information
Users Browsing this Thread
There are currently 1 users browsing this thread. (0 members and 1 guests)
Similar Threads
-
Oil Pressure opinions wanted
By transamdave in forum Firebird / WS6Replies: 27Last Post: 06-09-2014, 09:25 AM -
Opinions and/or advice wanted...
By greasepunk in forum Firebird / WS6Replies: 7Last Post: 08-01-2011, 03:08 AM -
NBM Camaro Owners, and Opinions Wanted
By Matt in forum Appearance SectionReplies: 2Last Post: 07-23-2007, 04:02 PM -
opinions wanted
By stevegrizzle in forum Kill StoriesReplies: 35Last Post: 09-25-2006, 10:55 AM -
Opinions Wanted Please
By ViperBite4 in forum Firebird / WS6Replies: 10Last Post: 03-15-2006, 12:46 PM
Bookmarks