Results 4,161 to 4,180 of 7102
-
06-28-2015, 05:38 PM #4161
-
06-28-2015, 05:41 PM #4162
-
06-28-2015, 05:46 PM #4163
-
06-28-2015, 05:47 PM #4164
- Join Date
- Feb 2009
- Location
- Florida Man Status Acheivement
- Posts
- 11,759
Navy Blue Metallic- 98 T/A w/ mods, 00 FBVert
Well I found my strange noise and jerking from the drive train.
Rubbing no bueno..
In the end spent 4 hrs triming & grinding to make the TA mount work with the 8.8 housing and the drive shaft plate.
-
06-28-2015, 06:52 PM #4165
Cleaned up my engine bay a little, dressed the plastics in Meguiars Hyperdressing.
Decided to look the lower half of the car over some and noticed my front tires are dated the 24th week of 2007... Definitely some plans to update those then. Might get the Nitto NT555s to match the rear, or considering the BFG KW2s, but I am more partial to having a full matching set.
Also found what I believe to be a bad pinion seal.
2000 Trans Am WS.6 M6
SLP lid & bellow w/ K&N, GMMG catback w/ Corsa Clones, UMI SFC, UMI Adj. Panhard, UMI Adj. TQ arm w/ relocation kit, QTP Longtube headers ORY, LS6 intake, EGR/A.I.R delete.
Eibach prokit, Bilstein HDs, Nitto NT555s, skip shift elim, whiteface overlays, 20% tint, matte black decal/overlays
YouTube.com/DarrenWS6
-
06-28-2015, 08:02 PM #4166
- Join Date
- May 2013
- Location
- Nashville, TN
- Posts
- 1,434
Black / White- '00 T/A M6/'19 Hemi Truck
2000 Black TA M6 - LT's, ORY, UMI Short Stick, TT2's, Drilled/Slotted Rotors, Braided Lines, and Tuned by Vengeance SCCA and Car Show Approved
2019 Ram 1500 Crew Cab Laramie Limited
2015 Ram 1500 Crew Cab Sport Premium Hemi - Sold
2010 Hemi Crew Cab Sport Premium - Tuner and HID's - Sold
06 Quad Cab HHHHemi - Sold
99 Hugger Orange Camaro - Sold
97 Camaro - Sold
-
06-29-2015, 01:07 AM #4167
-
06-29-2015, 02:47 AM #4168
Darren - a leaky pinion seal was a GM factory installed option on our cars. They all seem to do it.
Engine bay looks great!
-
06-29-2015, 02:52 AM #4169
-
06-29-2015, 03:48 AM #4170
-
06-29-2015, 04:37 AM #4171
-
06-29-2015, 04:41 AM #4172
I have noticed in some photos of stock cars that there is often a small black box type thing next to the AC canister. Mine not having it right there. I do like how it looks without. Will plan on the air hose line for the cats to be removed, and the computer wire hide mod.
-
06-29-2015, 05:08 AM #4173
-
06-29-2015, 06:15 AM #4174
-
06-29-2015, 06:04 PM #4175
-
06-30-2015, 02:39 AM #4176
The important thing is that after you adjust the master cylinder to make sure the squat switch makes contact with the clutch pedal, you have to have the cover trim off to see it and you can follow the pedal up and see where it is. This switch is what disengages the cruise control when the clutch is depressed.
-
06-30-2015, 03:22 AM #4177
When I swapped out our A4 for a new Performabuilt unit the locator pins were seized... bad. With all the bolts out the transmission would not budge. I ended up driving the pins out of the back of the block with the blunt tip of an air chisel while a friend rocked the transmission back and forth by the tail stock.
-
06-30-2015, 02:52 PM #4178
- Join Date
- Apr 2011
- Location
- Johnstown,PA
- Age
- 54
- Posts
- 1,104
Silver- 1999 Trans-Am, 2012 Sonic
You got that right. No more oil under the rear, changed the tail shaft seal no more oil under the tranny, replaced my PCV system with a LS6 set up no more oil under the bell housing, found a leak from my oil catch can no more oil there. Just left with the leaking oil pan gasket and that's a job so for now I'm ok with a few drips.
That is exactly where it goes. And yours is missing...Look behind the PCM that's where it can be tucked away.99 Trans Am, SLP Lid, Blackwing filter, smooth bellow, Ported TB, LS6 intake, Ws6 lower ram air box, OBX LT's, Magna Flow cat back, LS7 clutch, Tick MC, Hurst Shifter, Frost Tune, UMI SFC,LAC, STB, PB, Torq Arm, Super Hawk hood, Torq Thrust II, Kee Audio.
Strange S60 4:10's, D&S Rotors, S/S Brake Lines.
Nitto NT05R Track Tire's, 12.7 @ 108 / 1.82 60'
Wish list.
Coil overs, Heads & Cam
-
06-30-2015, 04:09 PM #4179
I have the jig I built for hanging the motor in the engine bay if you decide you want to tackle the oil pan seal sometime.
-
06-30-2015, 05:07 PM #4180
Thread Information
Users Browsing this Thread
There are currently 5 users browsing this thread. (0 members and 5 guests)
Similar Threads
-
new guy just got my first trans am today
By roger_johnson2002 in forum New Member IntroductionsReplies: 9Last Post: 07-14-2011, 08:35 AM -
Found this on the windshield of my Trans Am today
By ls1camino in forum Almost Anything GoesReplies: 60Last Post: 03-10-2009, 12:11 PM -
Got into an accident in the Trans Am today
By ls1camino in forum Almost Anything GoesReplies: 30Last Post: 09-21-2008, 04:32 PM -
Just got my Trans Am today!
By vannatte in forum Firebird / WS6Replies: 34Last Post: 09-20-2007, 09:57 AM -
First time at Track today!!! 2000 Trans Am ws6
By gimmeadonut in forum Drag RacingReplies: 1Last Post: 11-12-2005, 01:34 PM
Bookmarks