Results 4,021 to 4,040 of 7102
-
04-11-2015, 02:51 PM #4021
I think the Russell lines for ABS/TCS were around $110 or so when I bought mine a few years back.
-
04-15-2015, 07:51 PM #4022
Spring clean up pinnacle wax, vacuum, interior cleaning
02 Black Trans Am Firehawk #1079.Lots bolt ons, NOS
Just one nasty chicken!!!!!
-
04-16-2015, 02:48 AM #4023
Sharp!
-
04-18-2015, 04:46 AM #4024
I'm really digging the wheels. I guess thats because my ride is also black.
-
04-18-2015, 05:10 AM #4025
The wheels are CCW classics with shot pink black centers 18x10 in rear
-
04-18-2015, 05:22 AM #4026
Nice. They are pricey, but I guess anything nice is expensive. LOL.
-
04-18-2015, 05:55 AM #4027
What did you do with your Trans Am today?
CCW website says around 800 each
Plus $50 per wheel for a colored insert
Last edited by naperws6; 04-18-2015 at 05:57 AM.
-
04-18-2015, 11:14 AM #4028
- Join Date
- Nov 2014
- Location
- near Fort Hood, TX
- Posts
- 412
blue- 2002 Trans Am
Got a/c vent on center right replaced. Can now direct air on passenger side, well wifie is happy
ASh
-
04-18-2015, 11:15 AM #4029
- Join Date
- Nov 2014
- Location
- near Fort Hood, TX
- Posts
- 412
blue- 2002 Trans Am
2002 auto T/A custom blue, Moser 9in rear end with 31 spline axle and 3.73 gears, Diablo Sport InTune, SLP LM1 catback, SLP lid & bellow, ram air free mod, eibach pro kit springs, bilstein hd shocks, bmr rear sway bar, bmr 2pt SFC bolt on, silver checker stripes 17x9.5 C5 Vette rims.
-
04-18-2015, 01:01 PM #4030
Installed UMI rear control arms and Panhard bar
98' Trans AM RIP
00' WS6/Black/Pacesetter LT's/Magnaflow Exhaust/SLP lid/Nick Williams 92mm TB/FAST 92 Intake/BMR Strut Tower Brace/BMR Rear LCA's/BMR Panhard Bar
-
04-18-2015, 02:17 PM #4031
- Join Date
- Feb 2009
- Location
- Florida Man Status Acheivement
- Posts
- 11,759
Navy Blue Metallic- 98 T/A w/ mods, 00 FBVert
What did you do with your Trans Am today?
Gave the neighbors a loud "Good Afternoon!!" watm up idle with open headers...
http://www.ls1.com/forums/f7/my-6-liter-build-174257/
http://www.ls1.com/forums/f8/my-8-8-rear-build-165553/
6.0L Block - Forged 403ci , Polluter Stg3 Cam, FAST 102mm Intake, NW102 TB, MSD wires, NGK TR6 plugs, Truck Coil Packs, LS3 Fuel Injectors, CC Pacesetter LT Headers, TS&P ORY, QTP e-Cutout, Magnaflow Muffler, 104mm Air Lid & Line Lock, Catch Can, Stage 2 T56 w/Viper shaft, PRO 5.0 Shifter, Tick MC, SPEC Stg3+ Clutch, QT SFI BH, MWC DSL, Full UMI Performance Suspension, Belstein Shocks, Hotchkis Springs (1" Drop), YR1 Snowflake Wheels wrapped in NT555 tires & Custom Fab Ford 8.8 rear w/Wavetrac Diff 3.73 Yukon Gears, WSQ Hood, 3"CM Strange Eng Drive Shaft.
00 FB Vert - Stock
78 FB - Just getting started......
Horsepower never lies, but is often lied about!
-
04-18-2015, 06:00 PM #4032
Out for a sunset ride with the top down and the wife in the passenger seat. Confirmed there are still way too many people living in this area who just seem to be wandering aimlessly around the roads with no particular destination in mind.
-
04-19-2015, 11:06 AM #4033
Awoke the beast from its winter nap. All cleaned up now and ready to go for a ride this afternoon.
-
04-19-2015, 04:21 PM #4034
- Join Date
- Jan 2015
- Location
- West Fargo ND
- Age
- 49
- Posts
- 7
red- 2001 ws6
-
04-19-2015, 05:14 PM #4035
Looks great! Same system on our car - love the look and the sound.
-
04-19-2015, 06:43 PM #4036
God I love red ws6's
-
04-20-2015, 07:25 PM #4037
New performabuilt transmission goes in this week. Also changed out the drls, back up, and tail lights with leds. And got new drl housings in the mail today.
-
04-20-2015, 09:15 PM #4038
- Join Date
- May 2013
- Location
- Nashville, TN
- Posts
- 1,434
Black / White- '00 T/A M6/'19 Hemi Truck
Found out my driver side taillight lens decided to separate from the housing...was washing my car and noticed that every time I'd dry the bumper, water would come out of the tail light area...after looking into it, the tail light was actually holding water and I could see the separation.
Guess I need to pull that off and reseal it this weekend before it gets worse...I still haven't installed my new DRL housings I got in the mail last week either.2000 Black TA M6 - LT's, ORY, UMI Short Stick, TT2's, Drilled/Slotted Rotors, Braided Lines, and Tuned by Vengeance SCCA and Car Show Approved
2019 Ram 1500 Crew Cab Laramie Limited
2015 Ram 1500 Crew Cab Sport Premium Hemi - Sold
2010 Hemi Crew Cab Sport Premium - Tuner and HID's - Sold
06 Quad Cab HHHHemi - Sold
99 Hugger Orange Camaro - Sold
97 Camaro - Sold
-
04-21-2015, 06:47 AM #4039
- Join Date
- Feb 2009
- Location
- Florida Man Status Acheivement
- Posts
- 11,759
Navy Blue Metallic- 98 T/A w/ mods, 00 FBVert
Pat, I took my tail lights off, using a 1/8" drill bit on the under side I drilled 3 holes, one under the reverse light and 2 for the brake and signal lights. Not all the way just enough to open drain holes for the housing, never punched into the reflective inside, maybe 1/4" to 3/8". This allows an any water that may get inside to drain out. now for the top I used a black rtv that I applied a thin bead. I haven't had any issues since.
Sunday I was able to able to back the bird out of the garage for the first time since I got the motor back in. Yesterday I had a couple from the up the street doing their evening walk stop and ask when I got the new car....I thought they meant the Durango or the Grand Prix at first, the guy says no the Trans Am I told them the back story and he was like damn, I don't think I could have the patients to kept a car that long.....
-
04-22-2015, 07:41 AM #4040
- Join Date
- May 2013
- Location
- Nashville, TN
- Posts
- 1,434
Black / White- '00 T/A M6/'19 Hemi Truck
First I want to thank Scott for shooting me some pics of the back of the DRL housings while he had his bumper off...helped a lot
Fixed my tail light last night that decided to split from the housing...I also decided to install these while I was at it since they have been sitting in a box for a month. Wish I would have done it a long time ago because they made a HUGE difference.
Old:
New:
I also found a WS6 hood about 2 hours away that I'm going to probably buy this weekend...was going to go with 2 big inlets instead of a WS6 style hood but I cant pass up the deal I found.Last edited by theorangeguy; 04-22-2015 at 07:46 AM.
Thread Information
Users Browsing this Thread
There are currently 4 users browsing this thread. (0 members and 4 guests)
Similar Threads
-
new guy just got my first trans am today
By roger_johnson2002 in forum New Member IntroductionsReplies: 9Last Post: 07-14-2011, 08:35 AM -
Found this on the windshield of my Trans Am today
By ls1camino in forum Almost Anything GoesReplies: 60Last Post: 03-10-2009, 12:11 PM -
Got into an accident in the Trans Am today
By ls1camino in forum Almost Anything GoesReplies: 30Last Post: 09-21-2008, 04:32 PM -
Just got my Trans Am today!
By vannatte in forum Firebird / WS6Replies: 34Last Post: 09-20-2007, 09:57 AM -
First time at Track today!!! 2000 Trans Am ws6
By gimmeadonut in forum Drag RacingReplies: 1Last Post: 11-12-2005, 01:34 PM
Bookmarks