WANTED: more technical sticky write-ups

[35th-ANV-SS]

http://www.ls1.com/forums/f66/instal...4/#post2699514

Gonna try my best to get that master installed this weekend

Good job Alex. I'll be looking forward to your MC write-up as this is a must for me at this point. Note how long it takes you too!

[tatertot91]

Good job Alex. I'll be looking forward to your MC write-up as this is a must for me at this point. Note how long it takes you too!

will do. got someone waiting for my stock mc so I may actually get the swap done lol

[35th-ANV-SS]

Nice! Always a plus to be able to put the OEM parts to good use. I'm still sitting on OEM springs/shocks/torque arm/drive shaft/air pump/grille/LCA's/SLP MAF/SLP Blackwing lid/K&N filter myself

[tatertot91]

sticking up a little huh
mc is actually getting used to mock up a tilton mc to basically replicate the tick mc
should be put to good use

[tatertot91]

Finally got my master installed, only been 7 months it's been laying around

http://www.ls1.com/forums/f65/master...3/#post2700903

[Cutlass]

nice work! its stickied!!

[tatertot91]

nice work! its stickied!!

Thanks i'm tryin'

[RedFenix_68]

I have posted a tear down of the T-56. Reassembly coming soon.

[Cutlass]

I have posted a tear down of the T-56. Reassembly coming soon.

Nice! Looks good so far.

[RedFenix_68]

Nice! Looks good so far.

I will be tearing more of it down and adding much more to it later.

[Firebirdjones]

Wow, I forgot all about this thread until the email notification I got a few minutes ago.

Most of what I do is on classic stuff so write ups of things I'm doing may not pertain to the board. I do however have another LS swap coming up, sticking it into a 57 T-bird.

Other than the LS swap I did in my blazer, and the 12 bolt I already built (and forgot I had mentioned that for a write up), Otherwise it's been non stop paint work for me, nothing anyone would be interested in.

[RedFenix_68]

Wow, I forgot all about this thread until the email notification I got a few minutes ago.

Most of what I do is on classic stuff so write ups of things I'm doing may not pertain to the board. I do however have another LS swap coming up, sticking it into a 57 T-bird.

Other than the LS swap I did in my blazer, and the 12 bolt I already built (and forgot I had mentioned that for a write up), Otherwise it's been non stop paint work for me, nothing anyone would be interested in.

To bad your not closer i could use some paint work on top of my Trans am. Not the sail panel but the t-top assembly in the middle.

[Firebirdjones]

To bad your not closer i could use some paint work on top of my Trans am. Not the sail panel but the t-top assembly in the middle.

Swamped with paint work. I like the small jobs like yours, I can knock those out fairly quick and cheap.

Right now I'm going to be burried with 2 new jobs, a 64 chevy shortbed to paint and a 72 ford shortbed to paint.

[Knight]

I'll be doing a clutch swap soon, so I'll be certain to document that.

[RedFenix_68]

Swamped with paint work. I like the small jobs like yours, I can knock those out fairly quick and cheap.

Right now I'm going to be burried with 2 new jobs, a 64 chevy shortbed to paint and a 72 ford shortbed to paint.

If I send that part to you in a box do you think you could paint it? Obviously you would get paid...unless you had left over paint haha.

[RedFenix_68]

Swamped with paint work. I like the small jobs like yours, I can knock those out fairly quick and cheap.

Right now I'm going to be burried with 2 new jobs, a 64 chevy shortbed to paint and a 72 ford shortbed to paint.

Because if I shipped it, it would not cost much bc it is not bulky or very heavy. Same thing with my headlight cover. I have to take a ding that was self inflicted from a frustration error (very regretful afterwards). And do you or can you add flames or anything special like graphics or even paint the firebird?