Results 81 to 100 of 250
-
10-14-2009, 03:45 PM #81
- Join Date
- Apr 2008
- Location
- Fairhope, Alabama
- Age
- 32
- Posts
- 779
Black- 2002 Camaro SS SLP
I never got it dyno'd. But it did picked me up 3 tenths in the 1/8.
2002 Camaro SS A4 - SLP# 2951 l MS4 l LT's w/ORY l F.A.S.T 78 & TB l Borla l Cutout l CME l TCI 3500 l 3.23's l !emissions l !sway
-
10-14-2009, 05:07 PM #82
you getting past 7.5 in the 1/8 with your setup? 7.80's are my best so far with stock manifolds, but similar mods as yours.
that's with mt et's though.
-
10-14-2009, 05:17 PM #83
- Join Date
- Apr 2008
- Location
- Fairhope, Alabama
- Age
- 32
- Posts
- 779
Black- 2002 Camaro SS SLP
7.79 @83, on street tires. "Nitto NT555" 1.82 60ft. Its a 600 ft 1/8 track though. I got a cutout and a tune, so i should be in the mid 7.5's.
-
10-15-2009, 07:04 AM #84
Yeah, I had it blocked off. Til one day I hear ticking in my bay and the EGR pipe was bouncing up and down. Would've been a shit ton easier if the thing fell off before I installed em. Only cost me $20 to have it welded shut, but removing and installing em again was a PITA
Did it fall off when it was on your car?
-
10-15-2009, 07:54 AM #85
- Join Date
- Nov 1999
- Location
- over here...
- Age
- 45
- Posts
- 25,709
[]D [] []V[] []D- 1999 trans am
i heard what i thought was ticking and my SES came on... so i was all for the day... night time rolled around and i started my car up thinking it was a plug wire that got burnt through... then i seen the flames shooting out of the egr tube... it wasn't all the way off at that point so i took some copper wire and rigged it so that it was closed and the SES light would go out... had to wait a few days untill phoenix performance could fit me in to have it welded closed... it fell off onmy way there...
-
10-15-2009, 02:54 PM #86
-
10-15-2009, 05:42 PM #87
I put these on my car this past spring,they fit great!I did have to elongate the last bolt hole on the drivers side though.That was the only issue I had.I hooked them up to an Edelbrock ORY-took some fabbing to do,but was worth it to get it tucked up tight.My car is lowered 2 inches all the way around and only rubs on serious dips or high bumps!I installed it with the Flowmaster cat-back,honestly not real happy with the raspy sound!
-
10-15-2009, 07:13 PM #88
Haha, why couldn't it have just been easy for us and do it before their installed. It's weird they both fell off. I knew that piece was flimsy, but I wonder what caused it to do that. Your lucky it fell off on the way there, mine was off for about 4 days. Tried clampin it down til I could get to a shop and fell off when I was tightening it. Stupid ass EGR
Thats why
Good to hear its a good setup for you, even when lowered
-
10-16-2009, 05:21 PM #89
-
10-17-2009, 04:16 PM #90
- Join Date
- Apr 2008
- Location
- Fairhope, Alabama
- Age
- 32
- Posts
- 779
Black- 2002 Camaro SS SLP
HA! New best! 7.54 @85 1.79 60' on street tires, and btw, the track is 60 feet short of a full 1/8..
-
10-19-2009, 05:59 AM #91
-
10-19-2009, 08:09 AM #92
-
10-19-2009, 08:43 PM #93
Just ordered mine last night will be throwing a H pipe and dual cutouts behide it but dont know what mufflers yet. Any suggestions?
-
10-23-2009, 08:28 AM #94
- Join Date
- Apr 2008
- Location
- Fairhope, Alabama
- Age
- 32
- Posts
- 779
Black- 2002 Camaro SS SLP
The EGR pipe on the passenger side broke off today, easy fix tho. Lifted the car up, and was able to weld the hole shut whithout taking the header off. Thats the only negative i have with these headers..
-
10-23-2009, 10:45 AM #95
All I can say.........You get what you pay for
┌∩┐(◕_◕)┌∩┐
Man: The Mods you are fighting,
they are the biggest Men I have ever seen. I
wouldn't want to fight them!
Me: That is why no one will remember your name!
-
10-23-2009, 07:30 PM #96
You, Spaz, & me can attest to the shitty EGR pipe, at least you didn't have to take off the header. I did, took a half hour to pull the header out, another 3 to reinstall it
Ya, but I'm not at the stage where I can spend $800 or more on just headers. I will when I can, but for the price I think they're great. I wanted LT's and these have been amazing so far
-
10-23-2009, 11:34 PM #97
-
11-01-2009, 07:42 PM #98
Will these work on those?
http://www.texas-speed.com/shop/item...d=190&catid=45
-
11-01-2009, 08:59 PM #99
- Join Date
- Jul 2006
- Location
- Tyler,Texas
- Posts
- 116
Black on Black- 2001 Trans Am ws6
OK im jumping in too i think this is awesome that they are so cheap and will have the long life that SS offers. so im going to weld the egr up before i put them in im a welder so yay for me. Is there anything I will need to do if I delete the egr??? Where can I get a good set of header bolts
-
11-02-2009, 06:18 AM #100
Thread Information
Users Browsing this Thread
There are currently 1 users browsing this thread. (0 members and 1 guests)
Similar Threads
-
"Ludicrous Speed" is an option now
By SMWS6TA in forum Almost Anything GoesReplies: 11Last Post: 07-21-2015, 04:10 PM -
"shorty headers" ot "manifolds"?
By carls02tafirehawk in forum External EngineReplies: 2Last Post: 09-10-2006, 12:22 PM -
Anyone using "ebay" headers ?
By 00Hawk#140 in forum External EngineReplies: 2Last Post: 07-07-2006, 09:27 PM
Bookmarks