Results 1 to 12 of 12
Thread: stroker question
-
03-01-2008, 07:53 AM #1
- Join Date
- Feb 2008
- Location
- orange county
- Posts
- 14
600hp sube power sancar- 68 panel,
stroker question
just purchased a ls6 5.7 block i see alot of kits to purchase that will make this a 383 stroker. are there any out there that will make this 406 stroker or is that just for the ls2 blocks.
-
03-01-2008, 09:46 AM #2
-
03-01-2008, 01:28 PM #3
You gotta sleeve it to bore it that much I do believe.
-
03-01-2008, 08:37 PM #4
- Join Date
- Dec 2007
- Location
- Austin, TX
- Posts
- 92
Pewter- 2002 Trans am WS6 T-top
sleeve it
On that mill, all you can go is 383 cubes. Anything else and you will need a ls2/6.0L iron block, to go a stroker.
-
03-01-2008, 09:18 PM #5
- Join Date
- Feb 2008
- Location
- orange county
- Posts
- 14
600hp sube power sancar- 68 panel,
after further research i found that the 406 stroker was 6.0l i did order a stroker kit for a 383 thanks guys
-
03-05-2008, 09:03 PM #6
I just finished my 396 stroker, thats with a 3.903 bore on a stock LS6 block. I used a 4.125 crank your 383 uses a 4.000 stroke
Eagle makes a 393 stroker kitMike Berry
2000 TransAm WS6 A4
ASC#6552
-
03-05-2008, 09:19 PM #7
- Join Date
- Feb 2008
- Location
- orange county
- Posts
- 14
600hp sube power sancar- 68 panel,
you got yur kit from eagle? did you have to dao any clearancing? anything special you have to do.
-
03-06-2008, 10:14 PM #8
- Join Date
- Dec 2007
- Location
- Austin, TX
- Posts
- 92
Pewter- 2002 Trans am WS6 T-top
Thats cool that you can stroke it that much out on that bore. Only down side is that its not a square motor. I wonder if there will be any type of premature wear issues. I bet the liners had to be cleared for the connecting rods.
-
03-08-2008, 01:51 PM #9
how much hp will a stock ls1 block hold before grenading?
Red '02 Camaro Z-28
Black '06 H.D. Streetglide
Vibrant Blue '07 Dodge Hemi Crew Cab
-
03-08-2008, 08:55 PM #10
no premature ware, thats why I used 6.250 rods, for the rod angle to the cylinder wall. thats also why Eagle uses a 6.200 rod on there 393 stroker kits
I used a Callies crank, lunati rods and pistons
-
03-13-2008, 09:49 AM #11
-
03-14-2008, 03:36 AM #12
- Join Date
- Aug 2005
- Location
- Billings,MT
- Posts
- 428
Sunset Orange Metalic- 2002 Firehawk
12 psi of boost on a stock motor and #4 piston broke and cracked the liner and the block.12 psi was not smart on my part -- --- 402 stroker with forged internals is the next stop.
Thread Information
Users Browsing this Thread
There are currently 1 users browsing this thread. (0 members and 1 guests)
Similar Threads
-
stroker question MPG
By Hawaiianz28 in forum Internal EngineReplies: 8Last Post: 09-14-2008, 05:50 AM -
Question: Stroker Question
By architect7 in forum Internal EngineReplies: 18Last Post: 08-06-2008, 08:20 PM -
Stroker question
By grandkodiak in forum LT1Replies: 28Last Post: 07-01-2008, 10:08 PM -
Stroker Question??
By Camaroride32 in forum Internal EngineReplies: 2Last Post: 12-05-2007, 12:59 PM -
Ls1 383 stroker question
By 99Ls1fever in forum Internal EngineReplies: 65Last Post: 11-16-2007, 07:59 PM
Bookmarks