TT halted ugh but yay.....

[Smittro]

Does the accumulated fuel act to richen the intake charge, or does it boil off? Would be neat to watch this on a high speed camera to see what actually happens.

Sheet metal intake in the works?

It prolly boils off somewhat but gets recharged so to speak when it's time for that set of valves to open and gets a fresh shot. If there is any heated fuel left, I would imagine that this would possibly make the "fresh" shot more explosive, and possible where some of the engines HO power came from. 200-210hp, for the Multi Porters, and only a small gain from the sequential injection to about 215hp, with slightly better flowing heads. Although when compairing the two different heads (older to newer) I could'nt really see a difference. Both sets have massive intake ports. But the newer LQ1's (TDC) had a better larger port primary (lower) intake. But the gasket area of these is a poor (thin walls) design, and notorious for leaking top and bottom. The older ones though they have smaller openings on top had more gasket area which made for a better seal IMHO.

I dunno maybe custom steel or aluminum intake. Still on the drawing board, as to flow and injector placement. I'd like to utillize the three shot for each open set of valves though rather than the pooling effect it had..

[GTP231]

The shot ends up just laying on the valves that are closed. The GM idea is that when they fire @ least one set (2 intake per cyl) of valves will be open. The old set up from GM fired all 6 @ once, I've just narrowed it down to 3 basicly making the old rumor a fact lol. Yeah I know it sounds strange but that just how it is in the 92 TDC lol. Later years had sequential injection and eliminated the "all @ once" injector firing. The plan for me now is to move the injectors out of their ports and fire 3 when one set of valves is open rather than letting it pool on the valves that are closed.

With no after market intakes made guess who has to make a custom intake too wink wink..

Advantage 94+ cars Sequential from the factory for the higher power numbers

[Smittro]

Advantage 94+ cars Sequential from the factory for the higher power numbers

Yeah 5 more than the old 5spd and 15 more than the old auto's = not much lol, also the rev limiters on the 94+ cars is almost 1000 rpms lower..

[GTP231]

Yeah 5 more than the old 5spd and 15 more than the old auto's = not much lol, also the rev limiters on the 94+ cars is almost 1000 rpms lower..

I've heard of some of the 94s hitting 7 unless they're tachs are insanely off

[Smittro]

I've heard of some of the 94s hitting 7 unless they're tachs are insanely off

Me too but it has to be happening between gears rather then durring a pull and they were also limited to 110 top speed.. Been past 125 a handfull of times in the 92, bounced the needle off the bottom a few with the chip, comp, cai, and exhaust too.

[Smittro]

An old buddy of mine had a 98 (ish) grand am gt tdc stupid thing was set to shift @ like 6200. Which comming out of first hitting second was far to early @ 4200 ish which is just a hair outside the sweet spot in the tdc, so it would lay down for a sec then come alive again.

[GTP231]

Me too but it has to be happening between gears rather then durring a pull and they were also limited to 110 top speed.. Been past 125 a handfull of times in the 92, bounced the needle off the bottom a few with the chip, comp, cai, and exhaust too.

Mine shut off at 118 stock

Grand Am with a swap? Mine shifted around the same

[Smittro]

Mine shut off at 118 stock

Grand Am with a swap? Mine shifted around the same

I dunno buddy could'nt get more than 110 brand new car @ the time all stock..

[suede]

you bout got this dam thing done yet?

[Smittro]

you bout got this dam thing done yet?

Gettin there about another month of work should be done or near to it..

[pajeff02]

Picked up a set of EFI and Tuning books last week -- one chapter talks about batch injection and gives a pretty good description of how the system works and what happens to the fuel between intake events. You get that thing done and I may have to take a ride south to check it out.

[Smittro]

Picked up a set of EFI and Tuning books last week -- one chapter talks about batch injection and gives a pretty good description of how the system works and what happens to the fuel between intake events. You get that thing done and I may have to take a ride south to check it out.

Deal! Look under it's coverage for speed density, it's old GM obd1 stuff should cover it in detail..

[GTP231]

Gettin there about another month of work should be done or near to it..

Pics?

[Smittro]

Pics?

None yet, not much has changed been busy as of late..

[Bad Co.]

Bro, tt'n a v6 camaro is so f'n gnarly. I'd call it a jr. street sweeper. When you git it built and tuned an so forth, you have gotta post a youtube vid of the aftermath. i wanna hear that beast.

[Smittro]

Bro, tt'n a v6 camaro is so f'n gnarly. I'd call it a jr. street sweeper. When you git it built and tuned an so forth, you have gotta post a youtube vid of the aftermath. i wanna hear that beast.

Will do (going in my z34 tho) and thanx for the interest..

[Bad Co.]

Sorry bro . thought it was gonna go in a f-body. But i will tell you this, at least its not a ford. But good luck on gettin that beast together.

[Smittro]

Sorry bro . thought it was gonna go in a f-body. But i will tell you this, at least its not a ford. But good luck on gettin that beast together.

Thanx, There will never be a Ford in my parking lot. Unless I'm dead first..

[suede]

Thanx, There will never be a Ford in my parking lot. Unless I'm dead first..

I'll come over for a beer sometime... fix that lol

[Smittro]

I'll come over for a beer sometime... fix that lol

Bring a bottle 80 proof or better. Not much beer gets drank here lol..