Results 1 to 15 of 15
Thread: Post Pics Of Switch Panels
-
05-05-2007, 08:51 PM #1
Post Pics Of Switch Panels
any pics of the console ones or, ashtray, or custom which one do you guys like
-
05-05-2007, 09:20 PM #2
Here's what I used:
http://www.harrisspeedworks.com/shop...cat=320&page=1
-
05-08-2007, 08:45 AM #3
- Join Date
- Aug 2005
- Location
- O.C. California
- Posts
- 1,471
Black- 2002 Camaro SS (crashed)
-
05-08-2007, 04:41 PM #4
- Join Date
- Jul 2006
- Location
- Troy, OH
- Posts
- 11
pewter- 99 trans am
Soltakr how did you mount that switch panel in the ashtray I have those same switches will they fit down in there or did you make a plate for them or what. I was looking at the one from harris but if I can make this work that would be great.
-
05-09-2007, 07:06 AM #5
- Join Date
- Aug 2005
- Location
- O.C. California
- Posts
- 1,471
Black- 2002 Camaro SS (crashed)
Yea, I had to make a plate for it. Wasn't as easy as I thought it would be. haha
-
05-09-2007, 08:59 AM #6
-
05-09-2007, 09:25 AM #7
- Join Date
- Aug 2005
- Location
- O.C. California
- Posts
- 1,471
Black- 2002 Camaro SS (crashed)
I got it from RK sport.
-
05-09-2007, 05:21 PM #8
- Join Date
- Jul 2006
- Location
- Troy, OH
- Posts
- 11
pewter- 99 trans am
What did you make a plate out of plastic or aluminum or what, I think I might want to try this
-
05-10-2007, 07:16 AM #9
- Join Date
- Aug 2005
- Location
- O.C. California
- Posts
- 1,471
Black- 2002 Camaro SS (crashed)
I used carbon fiber and epoxy.
-
05-21-2007, 03:14 PM #10
- Join Date
- Aug 2005
- Location
- O.C. California
- Posts
- 1,471
Black- 2002 Camaro SS (crashed)
Here is closer look and the underside.
swithes
Gauge
Shifte console
-
05-21-2007, 04:25 PM #11
on pic 2 what is that fierglass mud?
and on pic 4 is that a home made carbon fiber, cause i see some holding tags on it.
great work
-
05-21-2007, 05:48 PM #12
How hard was it to mount all three things in the old cig. lighter cut out piece? I love the way that looks! Im also looking for a good way to mount/display gauge/purge switch and manual switch
-
05-22-2007, 07:23 AM #13
- Join Date
- Aug 2005
- Location
- O.C. California
- Posts
- 1,471
Black- 2002 Camaro SS (crashed)
In picture 2 it was this really tough epoxy, I don’t remember the name. What I did was cut out the stock frame and built one out of carbon fiber. The problem was the frame was too thin to drive screws through. I though about adding some bridge work but the taper on the sides was too far and didn’t have any anker points. Plus there is some stock electronic unit under that too. So I layered on the epoxy and through in a few carbon fiber spins to give some to grip and it worked. Looks like ass from under side. I use I could of trimmed off the fat and painted it but I was just glad it worked.
In picture 4 I used just a flat peace of carbon fiber and cut out the stock wall on the console. I left my some a little bit of edge on the stock unit to give the carbon fiber panel something to stick to using 3M tape all the way around. First I measured where I wanted the switch, gauge and bottom. Cut the temple and then polished out the c/f panel to give it some shine. Mounted in the new stuff and finished off with some quick disconnect wiring.
-
05-22-2007, 12:52 PM #14
-
05-22-2007, 01:24 PM #15
- Join Date
- Aug 2005
- Location
- O.C. California
- Posts
- 1,471
Black- 2002 Camaro SS (crashed)
Thanks, I cant take all the credit, I did have some help. Next time I'll just pay someone to do it.
Thread Information
Users Browsing this Thread
There are currently 1 users browsing this thread. (0 members and 1 guests)
Similar Threads
-
Electric cutout interior switch pics?
By TransAm11973 in forum General HelpReplies: 20Last Post: 12-08-2011, 12:06 PM -
Camaro Door Panels Recovered Pics
By Pewterss in forum Appearance SectionReplies: 10Last Post: 12-27-2010, 05:54 PM -
Pics of dimmer switch
By weberje in forum General HelpReplies: 0Last Post: 09-11-2010, 06:27 PM -
Switch to TA Door Panels?
By SuperSport346 in forum Appearance SectionReplies: 5Last Post: 03-22-2010, 06:10 AM -
Question: Any pics of cut out switch placement??
By allbaugh_04 in forum External EngineReplies: 17Last Post: 05-17-2009, 07:29 AM
Bookmarks