Results 1 to 12 of 12
Thread: Need Some Big Help!!!
-
10-16-2005, 05:39 PM #1BlueCrickett
- Join Date
- Sep 2005
- Location
- Port Huron/Michigan
- Age
- 39
- Posts
- 49
Teal- 1994 Trans Am LT1
Need Some Big Help!!!
I need to know what i need to get to turn my 1994 Trans Am to a carbruated 350?? I need a list on what i need to get and do any help would be greatly appreciated. dan_48422@ yahoo.com leave me one or hit up my email
Thanx Dan:
-
10-19-2005, 11:25 AM #2LSLurkerGuest
Umm....
-
10-21-2005, 05:22 PM #3Senior Member
- Join Date
- Sep 2005
- Location
- near St. Louis
- Posts
- 1,205
navy blue- 2002 Z-28 Camaro M6
Edelbrock makes a set up that is perfect for this-includes everything you need to convert the engine over to carb including the ignition conversion. They also make a couple of matched cams for this set-up.Hope you don't have to worry about emissions control testing anymore.Otherwise sounds cool to me.
-
10-21-2005, 07:14 PM #4BlueCrickett
- Join Date
- Sep 2005
- Location
- Port Huron/Michigan
- Age
- 39
- Posts
- 49
Teal- 1994 Trans Am LT1
thanx bro
-
10-22-2005, 10:10 AM #5BlueCrickett
- Join Date
- Sep 2005
- Location
- Port Huron/Michigan
- Age
- 39
- Posts
- 49
Teal- 1994 Trans Am LT1
Does that kit include if iam taking my LT1 engine out and replacing it with a 350 chevy that is already carbruated?????
-
10-30-2005, 05:57 PM #6Junior Member
- Join Date
- Oct 2005
- Location
- Detroit
- Age
- 51
- Posts
- 5
Black- 1993 Camaro
No, that kit is to convert the LS1 over to a carb. Funny, I am doing basicly the same thing, except I'm taking a V6 camaro over to a carb'd small block. I see everyone doing expensive conversions to LS1 and the such, I'm going cheap. For you, you really shouldn't need to do much. You can keep your stock computer in the car (not that it will do you much good), and you'll just need to wire the engine to your ignition. You should be able to use your stock p/s bracket and pump, and possibly your trans even. Not real sure on the Pontiac. Good luck.
Originally Posted by dan_48422
-
10-30-2005, 09:07 PM #7BlueCrickett
- Join Date
- Sep 2005
- Location
- Port Huron/Michigan
- Age
- 39
- Posts
- 49
Teal- 1994 Trans Am LT1
Thankx for the info!
-
12-03-2006, 08:14 AM #8Junior Member
- Join Date
- Dec 2006
- Location
- LI, NY
- Posts
- 2
black- 1936 ford
conversion
Jegs has the manifold and an msd setup to carbureate your ls1. Jegs part # 7118. I was going to do the same thing, but a bit too pricey.
-
12-03-2006, 09:35 AM #9Junior Member
- Join Date
- Dec 2005
- Location
- Atlanta, GA
- Posts
- 42
red- 2002 camaro ss
Isn't 94 an LT1?
-
12-03-2006, 10:31 AM #10Junior Member
- Join Date
- Dec 2006
- Location
- LI, NY
- Posts
- 2
black- 1936 ford
lt-ls
sorry about that, I'm not really a chevy person, just trying to get this project done. Of course, Lt1.
-
12-03-2006, 06:25 PM #11Rice Killa
- Join Date
- Aug 2006
- Location
- Myrtle Beach
- Age
- 34
- Posts
- 5,560
Black With T-Tops- 96 Z28 M6
Yea i think it was from 93-97 LT1 and 98+ was LS1 and before the LT1 was the 5.0 i dont know what name they had Originally Posted by rnl35thss
-
12-04-2006, 02:53 PM #12Junior Member
- Join Date
- Dec 2005
- Location
- Atlanta, GA
- Posts
- 42
red- 2002 camaro ss
Just thinking that should make it somewhat less complex. If swapping in a completely different engine, and a manual trans. it should be a piece of cake. If an auto trans, I would look into transmission controls in the PCM.
Reply With QuoteThread Information
Users Browsing this Thread
There are currently 1 users browsing this thread. (0 members and 1 guests)
Bookmarks