Results 1 to 20 of 26
-
11-21-2006, 04:46 PM #1
which gears are built for 1/4 mile
i am looking for gears that will make my camaro faster and lower rpm and improve my 1/4 mile time....need some help...thanks
-
11-21-2006, 06:39 PM #2
It would help to know what tranny you have and any other mods.
-
11-22-2006, 09:28 AM #3
it is a 6speed with almost stock everything...i just have a 160 thermostat and that is it for right now...the rear end is completely shot and i need to get a new one, housing and everything....
-
11-22-2006, 09:55 AM #4
-
11-22-2006, 03:06 PM #5
Unless your getting a used 10 bolt cheap (less than $300) get yourself a Strange 12 bolt with 4:11 gears.
-
11-22-2006, 03:23 PM #6
9inch w/ 4.10's. or moser 12bolt.
-
11-22-2006, 09:22 PM #7
how much hp will it be able to handle the moser and the strange 12 bolts....
-
11-22-2006, 11:20 PM #8
Get a 9" with 4:11's. It will help your 1/4 mile time but it won't lower your rpm's like you asked, it will raise them.
-
11-23-2006, 07:55 AM #9
A nine inch w/Detroit locker is pretty much indestructible.
-
11-23-2006, 09:07 AM #10
-
11-23-2006, 09:47 AM #11
-
11-23-2006, 10:15 AM #12
-
11-23-2006, 07:49 PM #13
could you send me a price also. are 4.11's good for daily drivers or just for drag racing
-
11-24-2006, 07:15 AM #14
You can daily drive 4:11's no problem. Depending on what options you go with figure on paying right around $2500 when it's all said and done. Mine has 35 spline axles, a spool, it was powdercoated, and came completely assembled with backing plates and 5/8" studs for that.
-
12-08-2006, 06:52 AM #15
is spool better or is a differential better....
-
12-08-2006, 12:33 PM #16
Better as opposed to what? For the street most people will tell you a diff is better because in tight turns a spool will have to break loose the inside tire to make the turn. If you keep it out of parking lots you should be fine. Mine is not a daily driver but it sees a fair amount of cruising around in the summer time and I prefer the spool. It always spins both tires and never needs rebuilt.
-
01-04-2007, 11:01 PM #17
i've constantly been told not to get 4.10 because "their not highway gears"
-
01-05-2007, 04:19 AM #18
-
01-05-2007, 09:45 AM #19
-
01-05-2007, 09:47 AM #20
Thread Information
Users Browsing this Thread
There are currently 1 users browsing this thread. (0 members and 1 guests)
Similar Threads
-
Help: about to change my plastic gears for brass gears
By edrvsqz1980 in forum General HelpReplies: 17Last Post: 07-18-2009, 05:09 PM -
Dyno Testing A Home-Built Pontiac Motor - Backyard-Built Bruiser
By Ed Blown Vert in forum Firebird / WS6Replies: 0Last Post: 06-01-2007, 10:00 AM -
Dyno Testing A Home-Built Pontiac Motor - Backyard-Built Bruiser
By Ed Blown Vert in forum Firebird / WS6Replies: 0Last Post: 05-18-2007, 07:10 AM -
Built GM 10 bolt with 4.10 gears.
By MISFIT in forum Parts For Sale / TradeReplies: 0Last Post: 09-17-2006, 02:06 PM -
3:73 gears, 3:42 gears, clutch, flywheel, plug wires
By ls1hater in forum Parts For Sale / TradeReplies: 4Last Post: 08-16-2005, 06:15 PM
Bookmarks