Page 1 of 2 12 LastLast
Results 1 to 20 of 27
  1. #1
    Junior Member
    Join Date
    Aug 2005
    Location
    Miami, FL
    Age
    44
    Posts
    62

    is a cutout worth the money?

    I have a 2002 ws6 with k-n-N air filter, air lid, LT headers, no cats, y-pipe, magnaflow exhaust, and LS1 edit. I want my car to sound a lot louder. Is a cutout worth the money and would it make my car a lot louder considering my setup. If so, where is the best place to get one. Thanks.

  2. #2
    Senior Member
    Join Date
    Jul 2005
    Location
    Jacksonville, FL
    Posts
    2,723
    You want to be louder!? Just kidding...cutouts are cheap...available from most sponsors/local speed shops...and probably will make you louder since it'll bypass the catback.

  3. #3
    Snake Eater
    Guest
    Quote Originally Posted by ram air ws6
    I have a 2002 ws6 with k-n-N air filter, air lid, LT headers, no cats, y-pipe, magnaflow exhaust, and LS1 edit. I want my car to sound a lot louder. Is a cutout worth the money and would it make my car a lot louder considering my setup. If so, where is the best place to get one. Thanks.

    I have a similar setup on my 01 TA. I thought my cut-out was well worth it. Pacesetter lt's, tsp ory, and magnaflow catback. I have a cut-out and it sounds REAL loud! Especially when you have the cut-out off and get up to the 2000 RPM range, it sounds like the borla, but SCREAMS!

  4. #4
    Rhino21149
    Guest
    My son and I put QTP electric cutouts on our Camaro - 408 FE block, 490 RWHP, 540 RWT. It is a lot of fun. You can sit in the car and a light and a little rice-burner buzzes up next to you and you just open the exhaust, and the sound changes from a ragged deep muffled idle to a sharp open-header bar as you give the throttle just a blip: very intimiating. Have to be careful, though if you get into it, is is totally-illegal loud and cops blocks away can hear you.

  5. #5
    Member silverTA2002's Avatar
    Join Date
    Sep 2005
    Location
    Bradenton, FL
    Age
    44
    Posts
    134

    silver
    2002 Pontiac Trans Am

    Worth it?

    It's like $35 for a cutout plus labor.

  6. #6
    Rhino21149
    Guest
    The electric cutouts cost about $169 a piece and are easy to install if you have the car on a lift.

  7. #7
    BBATCAR
    Guest
    It is personal taste, for me it was too loud in the cabin, others like it. I had a QTEC and it leaked so I sold it... they are fun but I couldn't take the exhaust leak when closed.....

  8. #8
    Old Skool like an 8-track A-BomB's Avatar
    Join Date
    Aug 2005
    Location
    Houston
    Posts
    179
    '05 Cadillac CTS-V

    they are worth the money.

  9. #9
    old timer blue02Z's Avatar
    Join Date
    Sep 2005
    Location
    Texas
    Age
    38
    Posts
    3,806

    Navy Blue Metallic
    2002 Z28

    what is the sound diff. between having one cut-out after the y or two after the collecters? what about a power diff?

  10. #10
    Rhino21149
    Guest
    Not much difference on that alone. the real difference is whether the cut out is a head or behind the cats. Obviously, one on the Y-pipe will be behind the cats - but either way its a lot quieter that way.

  11. #11
    Modding is an Addiction bww3588's Avatar
    Join Date
    Sep 2005
    Location
    Chillicothe, Ohio
    Age
    36
    Posts
    438
    Quote Originally Posted by Rhino21149
    My son and I put QTP electric cutouts on our Camaro - 408 FE block, 490 RWHP, 540 RWT. It is a lot of fun. You can sit in the car and a light and a little rice-burner buzzes up next to you and you just open the exhaust, and the sound changes from a ragged deep muffled idle to a sharp open-header bar as you give the throttle just a blip: very intimiating. Have to be careful, though if you get into it, is is totally-illegal loud and cops blocks away can hear you.
    i hope your not talkin about a ford FE block?

  12. #12
    Rhino21149
    Guest
    Quote Originally Posted by bww3588
    i hope your not talkin about a ford FE block?
    No, of course not, FE just means "iron" since it is the periodic table symbol for that element. The big V-8 iron blocks used in various years in the Silverado and Escalades are the identical castings to the LS-6 and LS-2 blocks of the same year. Just about everything fits: heads, pumps, pans, etc. The block weighs about 90 lbs more but has two advantages: 1) its a lot cheaper, 2) you can bore the cylinders a bit more than in the AA blocks, 3) its strong as hell which is important if you plan to abuse the engine.

    Our Camaro has a 408 (bored FE LS-6 block with 4" stroker) and AFR big-port heads, 11.5 c.r., all forged internals, Kocks big-diamter headers, etc., and makes about 512 RWHP on fuel and about 660 with nitrous, with the cutouts open, about 30 less blowing through the cats and mufflers.

  13. #13
    Junior Member
    Join Date
    Sep 2005
    Location
    Fort Stockton, Tx
    Age
    42
    Posts
    39

    Blue
    2000 Z-28

    Worth it!!

    I have Pacesetter LTs and ORY with stock catback and a flowmaster muffler. Actually sounds good through full exhaust, but much much louder through cut out. I just have the regular cutout (non-elec) paid about 35 bucks for it. It screams at WOT

    Be careful though very loud and illegal

  14. #14
    RED98WS6
    Guest
    I put a cutout on my WS6. It's a pretty cheap mod...$35 for the cutout, and another $40 to get it installed. It adds about 10 horsepower. Of course, you'll probably want to get a electric opener...another $200.

    I hardly ever use mine on the street. I open it up at the strip though. At least I can hear my engine better. The thing I like the best: sounds great at idle. The thing I like the least: It doesn't sound that great at wide open throttle. I like the sound of open headers MUCH better, either that or just full exhaust.

    Is it a worthwhile mod? Its a toss-up. If I were to do it all over again I would get the borla catback exhaust and and put a QTP cutout opener in the flange where the plates go. Just as good as a cutout.

  15. #15
    used and abused at wot ibanez7's Avatar
    Join Date
    Aug 2005
    Location
    Crystal Lake IL
    Age
    47
    Posts
    2,517

    Pewter
    2001 Camaro Z28 M6

    yes!!! nothing flows better!

    read my review
    http://ls1.com/forums/showthread.php?t=2029

  16. #16
    Junior Member OneBadZ's Avatar
    Join Date
    Sep 2005
    Location
    Missouri
    Age
    39
    Posts
    34

    White
    2000 Z28

    Quote Originally Posted by BBATCAR
    It is personal taste, for me it was too loud in the cabin, others like it. I had a QTEC and it leaked so I sold it... they are fun but I couldn't take the exhaust leak when closed.....

    I have dual qtec's and today will be the 4th time i have had to fix them. They are coming off for good. Going with lighter exhaust setup and will make more power.
    Scott
    00 Z28: FOR SALE
    99 SS: R.I.P.

  17. #17
    Junior Member OneBadZ's Avatar
    Join Date
    Sep 2005
    Location
    Missouri
    Age
    39
    Posts
    34

    White
    2000 Z28

    Quote Originally Posted by blue02Z
    what is the sound diff. between having one cut-out after the y or two after the collecters? what about a power diff?

    You will have almost zero ground clearance if you put dual cutouts right after the headers. You will have very little clearance if the dual cutouts are moved back. And from researching tons of posts from different forums and from my own 1st hand experience you must have atleast 12-15" of exhaust after the headers or it wont run just right, back pressure is a b!tch.

    One cutout in the I-pipe is worth .10 in the 1/4 mile.

  18. #18
    RED98WS6
    Guest
    Quote Originally Posted by OneBadZ
    I have dual qtec's and today will be the 4th time i have had to fix them. They are coming off for good. Going with lighter exhaust setup and will make more power.

    I had read all about qtec and their problems. Thats why I chose DMH:

    http://www.dmhperformance.com/

    I've been very happy with it so far

  19. #19
    Junior Member
    Join Date
    Sep 2005
    Location
    Fort Stockton, Tx
    Age
    42
    Posts
    39

    Blue
    2000 Z-28

    Just get a $35 cutout, if you want it to be loud as hell you can take the cap off. If you want to be quiet then put it back on. Depeding on what you have and plan on doing to your car the HP will not be a big difference, (it will NOT be noticeable), it is fun though. Can somebody logically explain back pressure and why it works? As far as I know, you just need to be able to get the air in and get it out as fast or faster.

    Sorry....you just want to get louder..... the cutout is worth it
    Last edited by HC2000Z28; 09-29-2005 at 11:03 PM.

  20. #20
    Snake Eater
    Guest
    Hi, I have the magnaflow cat-back. My cut-out is installed to the right of the muffler, just before all the air is exiting through it. Is this the correct position? AND- how much does this differ from the I-pipe installation?

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. Is this T/A worth the money?????
    By screaminbird in forum Firebird / WS6
    Replies: 15
    Last Post: 01-22-2011, 08:21 AM
  2. Question: whats the best electric cutout for the money
    By WICKEDLS1 in forum External Engine
    Replies: 16
    Last Post: 11-01-2010, 12:49 AM
  3. Heads really worth the money?
    By Speed_kills_WS6 in forum Internal Engine
    Replies: 6
    Last Post: 04-22-2010, 10:04 AM
  4. Is this worth the money?
    By Vols Fan in forum Forced Induction
    Replies: 3
    Last Post: 04-19-2006, 04:11 PM
  5. Are Koni's worth the money?
    By bad99ta in forum Suspension and Handling
    Replies: 11
    Last Post: 01-19-2006, 04:51 AM

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •