Results 1 to 16 of 16
Thread: Stand alone wiring harness
-
07-25-2012, 12:24 AM #1
- Join Date
- Apr 2011
- Location
- Norway
- Posts
- 16
- Corvette C5
Stand alone wiring harness
Is a buying a stand alone wiring harness worth the money or is it easy to modify the stock harness?
The engine is a 2001 LS1 from a Camaro SS.
Will be swapped into a BMW.
-
07-25-2012, 03:11 AM #2
With the correct schematics, an understanding of engine electrical systems, and patience you can certainly modify a harness. That being said, you are probably further ahead with an LS specific harness that you then interface with your chassis. Do you have the stock Powertrain Control Module (PCM) from the donor car?
-
07-25-2012, 04:38 AM #3
- Join Date
- Apr 2011
- Location
- Norway
- Posts
- 16
- Corvette C5
-
07-25-2012, 04:53 AM #4
Biggest issue will be interfacing your gauges. What transmission will you be running?
-
07-25-2012, 05:05 AM #5
- Join Date
- Apr 2011
- Location
- Norway
- Posts
- 16
- Corvette C5
-
07-25-2012, 05:22 PM #6
That certainly makes it easier as you won't have to worry about any interface issues. Any pics of the project?
-
07-25-2012, 10:59 PM #7
- Join Date
- Apr 2011
- Location
- Norway
- Posts
- 16
- Corvette C5
-
09-18-2012, 05:35 PM #8
- Join Date
- Mar 2012
- Location
- Jackson, MS
- Posts
- 168
Copenhagen Blau/Black- 88 Porsche 951/07 TBSS
I bought a LS1 stand alone harness book from F-Bodies Inc. on ebay for like 24$. I am currently in the process of doing an LS1 conversion into my Porsche. The book is pretty awesome. Has pinouts and all the modules and sensors laid out for you.
-
09-19-2012, 02:23 PM #9
Depends on the time you have on your hands
I've heard horror stories with electrical gremlins on some swaps, could have been shoddy workmanship though.
I've done handfull of retro swaps and just prefer now to buy a ready made stand alone harness. Figure there is less chance of a gremlin popping up, and I daily drive it so dependability is top priority.
I've used Howell for the last 3 swaps and I've been extremely happy. It's just like a factory harness, same color coded wires (so diagnostic later down the road can be done with factory manual) and all weather packs, wrappings, looms, just like OEM. (Some of the other vendors are not). Also comes with relays and fuses as needed.
What was nice also was that I used LS1 style dual electric fans which wasn't part of my 6.0 truck harness anyway. Sent Howell a picture of the weather pack connector for the fans and they made the harness with it. Everything labeled so it was just plug and play. Just tell them what vehicle it's going in and where you want to mount the computer. The harness is then made the correct lengths. Has always fit perfectly.
With electronic throttle body, they also made wires for cruise control as an added bonus, all I needed was a switch to run it. Everything labeled so it's simple plug-n-play. Definately worth the price to me.
-
09-19-2012, 07:24 PM #10
- Join Date
- Mar 2012
- Location
- Jackson, MS
- Posts
- 168
Copenhagen Blau/Black- 88 Porsche 951/07 TBSS
Hhhmmmm. Even I may have to check into that. Sounds pretty nice
Sent from my iPad using Tapatalk
-
09-19-2012, 07:36 PM #11
It's nice, but it's a little pricey too just like anything else worth having it seems. I thought they were in the realm of competative though when I checked around.
I can't put a link up, but if you google Howell Engine Management it comes up. They are up in Michigan.
-
09-21-2012, 02:29 AM #12
- Join Date
- Mar 2012
- Location
- Jackson, MS
- Posts
- 168
Copenhagen Blau/Black- 88 Porsche 951/07 TBSS
Cool sounds good. So they make me a complete new harness for my existing PCM or they provide a new PCM as well. I do have a full harness and PCM with the motor. If I decide to go tis roué guess I could sell to recoup some of the expense.
Sent from my iPad using Tapatalk
-
09-21-2012, 07:08 AM #13
Yeah the harness is all new stuff. You can do a GM computer from them or keep your own, that's up to you. They will tune the computer before shipment however if you go that route, so all unnecessary codes are eliminated, VATS, and other things so it's turn key and go. Their kit only had 2 or 3 wires to hook up which is typical of any retro swap you do.
One was for the fuel pump, and there was key on power, and a wire that takes power all the time. After running those where they needed to be, the rest was plug and play, mount your computer, fuse panel and relays where you want and you're done.
-
09-21-2012, 05:53 PM #14
- Join Date
- Mar 2012
- Location
- Jackson, MS
- Posts
- 168
Copenhagen Blau/Black- 88 Porsche 951/07 TBSS
That is sounding better and better even at the high cost
Sent from my iPad using Tapatalk
-
09-21-2012, 06:40 PM #15
I don't mean to shy you away from doing it yourself. It's not horrible to do with the schematics and pin outs in front of you and a little patients. I'm just too picky for my own good.
-
09-22-2012, 02:24 AM #16
- Join Date
- Mar 2012
- Location
- Jackson, MS
- Posts
- 168
Copenhagen Blau/Black- 88 Porsche 951/07 TBSS
Yea I had ya. I may end up doing it on my own still. One of my best buds was in the custom audio business for a long time so it's no problem for him to re-wire an entire car. I think I'll be recruiting him with some beer and pizza.
Sent from my iPad using Tapatalk
Thread Information
Users Browsing this Thread
There are currently 1 users browsing this thread. (0 members and 1 guests)
Similar Threads
-
quick stand alone harness
By Bigjohn366 in forum Computer & TuningReplies: 0Last Post: 11-01-2007, 12:09 AM -
ls1 wiring harness
By hotrod393 in forum Camaro / SSReplies: 0Last Post: 10-13-2007, 05:04 PM -
Wiring Harness
By BAD LT-1 in forum Parts Wanted / TradeReplies: 0Last Post: 10-07-2005, 09:56 AM -
WTB wiring harness
By RX-7 in forum Parts Wanted / TradeReplies: 1Last Post: 10-04-2005, 07:37 AM -
wtb, t56 wiring harness
By buck6680 in forum Parts Wanted / TradeReplies: 0Last Post: 08-02-2005, 06:52 PM
Bookmarks