Results 1 to 16 of 16
-
01-04-2012, 10:55 PM #1
- Join Date
- Oct 2011
- Location
- United States
- Posts
- 39
red- 2000 trans am
233/239 did a search found very little. need feedback
Hey guys got a tsp 233/239 cam getting ready to go in my trans am with all supporting mods. if you have this cam in your car how do you like it? does it pull nice and hard after 3k? just wanting some feed back on it havent been able to find to many running it.
-
01-05-2012, 11:23 AM #2
For stock cubes it should pull pretty good in the higher rpms for you...I ran a 238/242 in my ls1 and even though some would consider it on the big side, I liked it
-
01-05-2012, 08:30 PM #3
- Join Date
- Oct 2011
- Location
- United States
- Posts
- 39
red- 2000 trans am
awesome man thanks cant wait to start on it!
-
01-06-2012, 05:34 PM #4
I knew a couple guys that ran this cam with great results.
-
01-06-2012, 10:54 PM #5
- Join Date
- Oct 2011
- Location
- United States
- Posts
- 39
red- 2000 trans am
thanks for the replies.just stoked about the install and was wanting to hear some reviews. ill post up my dyno sheet when i get it tuned and some sound clips. its a 00 trans am with tsp long tubes,tsp true duals,ls6 intake manifold tsp 233/239 cam with supporting mods push rods, springs,timing chain and oil pump,slp lid,under drive pulley and 4.10 gears and going to have speed inc tune it. was hoping to put some heads on it this winter but budget won't allow so for now cam only hope its a stout car. car is stock ten bolt so ill keep my fingers crossed for now especially being a m6!
Last edited by 00redta88; 01-06-2012 at 10:58 PM.
-
01-07-2012, 06:38 AM #6
The car should run in the 11s cam only. Skip the heads and save for a rear end.
-
01-07-2012, 08:07 PM #7
- Join Date
- Oct 2011
- Location
- United States
- Posts
- 39
red- 2000 trans am
moser 12 bolt or ford 9" is in the near future. thanks for all the replies!
-
01-07-2012, 11:50 PM #8
- Join Date
- Apr 2010
- Location
- hawaii
- Posts
- 117
black- 2001 camaro ss
http://www.youtube.com/watch?v=NNVHwG3AU9k&feature=youtube_gdata_player
/\ my car /\
I have it and love it. I ran it in an auto with a yank ss3600 converter and it pulled like a freakin freight train from 3600 to 6500. With the converter unlocked it put down 378whp/345wtq w a M6 u should be right at 400whp and a high 11. 1st and 2nd will be useless on street tiresLast edited by 2NDSLPSS; 01-08-2012 at 12:25 AM.
-
01-08-2012, 11:03 PM #9
- Join Date
- Oct 2011
- Location
- United States
- Posts
- 39
red- 2000 trans am
awesome vid man! what other mods did you have? gettin pretty stoked! was just hoping this cam made decent under the curve as well
-
01-09-2012, 03:37 AM #10
I went with a Ford 9", 4.56:1 gears and 4 link in my GTO....still finishing up the swap...I hope I like it lol
-
01-09-2012, 02:17 PM #11
- Join Date
- Oct 2011
- Location
- United States
- Posts
- 39
red- 2000 trans am
that thing should pull like a f*ckin freight train!
-
01-09-2012, 02:17 PM #12
- Join Date
- Oct 2011
- Location
- United States
- Posts
- 39
red- 2000 trans am
I am going with 4.10's hope its enough gear!
-
01-09-2012, 07:23 PM #13
- Join Date
- Mar 2010
- Location
- St Pete, FL
- Posts
- 1,429
Bat mobile black- 2000 Trans am WS6 M6
I usually see most people going with 373s for street use, but many do have 410s. depends how much highway use you do i guess.. I personally would get 390s just because its right in between both.
-
01-09-2012, 08:05 PM #14
-
01-12-2012, 12:40 AM #15
- Join Date
- Apr 2010
- Location
- hawaii
- Posts
- 117
black- 2001 camaro ss
Under the curve was close to stock (converter locked, highway) 3000+ rpms was nasty ! also had prc dual valve springs titanium retainers, chromoly pushrods, tsp ported oil pump,ls6 timing chain, yank SS3600 converter, B&M shift kit & trans cooler, sfc's, spohn rear lca's, spohn PHB, P&P TB, pacesetter LT's, ORY, lingenfelter rear girdle.
-
01-12-2012, 01:04 PM #16
- Join Date
- Mar 2010
- Location
- St Pete, FL
- Posts
- 1,429
Bat mobile black- 2000 Trans am WS6 M6
Pretty sweet video.
Thread Information
Users Browsing this Thread
There are currently 1 users browsing this thread. (0 members and 1 guests)
Similar Threads
-
leaking antifreeze, answer not found in search..help
By staledog in forum General HelpReplies: 6Last Post: 01-08-2012, 02:42 PM -
WTB LS1 & Need Feedback
By bigpappy in forum Camaro / SSReplies: 8Last Post: 01-30-2009, 07:15 AM -
Need some FeedBack, Plz
By 02blackz in forum Camaro / SSReplies: 43Last Post: 09-21-2008, 06:18 PM -
Feedback on the 05/06 GTO's
By Tonys99RamAir in forum GTOReplies: 40Last Post: 03-17-2006, 09:53 AM -
My C5 n02 set-up. Feedback??
By Juiced2000C5 in forum NitrousReplies: 5Last Post: 01-03-2006, 03:58 PM
Bookmarks