Results 1 to 11 of 11
Thread: 10 bolt issues
-
08-02-2005, 06:52 AM #1WS SICKGuest
10 bolt issues
How expensive and difficult is it to replace the bearings on the differential?? My rear end is making a horrible sound and I had it checked and gears look fine, they say it may be the bearings?? Any help is greatly appreciated!!
Justin
-
08-02-2005, 05:24 PM #2
is the sound on just decelerating or what? It could also be a wheel bearing....
-
08-04-2005, 08:52 PM #3
When I did gears they replaced everything for a additional $100, so cost should be same as a gear change minus the cost of gears..so around $450.
-
08-13-2005, 07:44 AM #4
- Join Date
- Aug 2005
- Location
- Blairsville, GA
- Age
- 48
- Posts
- 215
Red- 2000 T/A WS6
Is it kinda like a WAAAA-WAAAA-WAAAA sound??? Does it speed up or slow down in moderate to sharp curves??? Could be axle bearings. They're easy to change with the right tools(slide hammer, wheel bearing puller attachment, 1/2",14mm,15mm sockets, ratchet, 8mm wrench,etc.), just time consuming, and you have to pop the diff cover to get to the C-clips that hold the axles in, which calls for replacement of gear lube.
At any rate, if it is axle(or wheel, either one) bearings, get the repair bearings. They'll ride on an unworn area of your axleshaft, and they have seals already installed. Keep in mind, you may have to replace a shaft if it's pitted like crazy from wear and tear.
Hope this makes you want a non C-clip axle as bad as I want one.
-
08-13-2005, 11:42 AM #5tommyz28Guest
Im getting the same noise i think, its on deceleration. It whines too but i have an aftermarket torsen with 3.73's I only get the noise on decel though?
-
08-13-2005, 11:47 AM #6
- Join Date
- Aug 2005
- Location
- Commerce Ga
- Age
- 47
- Posts
- 4,994
Black, Blue- 07 TBSS, 07 GSXR1000
I was getting the same noise only on decelaration. I took mine in and they are going to change all the bearings and while there in there I got a set of 4.10's to go in it. If it is free parts and labor then why not.
-
09-08-2005, 06:57 PM #7outlawz01Guest
Im on my fourth rear end. 10 bolt of course. and every time it starts makeing that sound about 3-4 weeks later either a bearing would freeze up or my pinoin would snap in half. It is only like 150-200 to have your bearings changed. only bc they have to basically tear it all apart. but try not to drive on it too long i did and lost my housing axles drive shaft and t-arm. all bc the pinoin snaped in half and my drive shaft and tranny went into free spin. but you might want them to check the axles and gears while they are in there.
-
09-09-2005, 11:02 PM #8Originally Posted by outlawz01
-
09-10-2005, 10:24 AM #9outlawz01Guest
There is a 2 month wait on moser 12 bolt. And i needed the car up quick. But the moser is coming soon.
-
09-10-2005, 10:25 PM #10
- Join Date
- Aug 2005
- Location
- Here and there
- Age
- 99
- Posts
- 15
Red- 2001 Z28
Replace ALL SIX bearings and races!! You only need some tools (you can never have enough tools) and a little know how. The bearings that come in our cars are shit. I did a complete overhaul on my 10-bolt with solid pinion spacer. that was 20,xxx miles ago not a peep out of it. The solid spacer does wonders for that tiny little 7.625 ring and pinion
Air tools
Press
Inch Lb torque wrench
Foot Lb torque wrench
brass hammer and punches
dead blow hammer
puller
bearing separators.
dial calipers
BTW great link here http://www.fullsizechevy.com/fscu/axletech/
-
09-19-2005, 05:32 PM #11
- Join Date
- Aug 2005
- Location
- Kentucky
- Age
- 71
- Posts
- 91
S O M- 2002 Camaro SS
The guy in my area who does f-body and vette work exclusively tells me that the crush spacer you use to preload the pinion gear cannot handle the torque and after the install it will crush further allowing play in the pinion and thus causing whining and ultimately failure. Do you guys have the solid spacer? I think Summit racing has it. A company in Cincinnati makes them. Around $18.
Thread Information
Users Browsing this Thread
There are currently 1 users browsing this thread. (0 members and 1 guests)
Similar Threads
-
Moser 12 bolt axle seal issues?
By pajeff02 in forum DrivetrainReplies: 14Last Post: 09-09-2013, 07:25 PM -
Moser 12 Bolt fluid issues
By deepblue in forum DrivetrainReplies: 2Last Post: 07-22-2008, 06:38 PM -
Bolt pattern issues
By Selride in forum Wheels and TiresReplies: 7Last Post: 07-14-2007, 09:39 PM -
Center bolt to Perimeter bolt Heads, Coil Mounting help
By juiced99ws6 in forum Internal EngineReplies: 7Last Post: 03-30-2007, 11:38 PM
Members who have read this thread: 0
There are no members to list at the moment.
Bookmarks