Results 21 to 30 of 30
Thread: Fog Light Replacement?
-
04-03-2008, 10:55 AM #21
-
04-04-2008, 04:35 PM #22
if you have a TA you probably need to get it from the top. i took off all that plastic crap and couldnt get to it from the bottom so i just turned the headlights on so they will flip up and you can get your arm straight down to it. i was wondering how you guys were getting it so easy from the bottom (wasnt thinking about the camaro having them on the outside)
-
04-04-2008, 05:00 PM #23
-
04-04-2008, 05:17 PM #24King 0f n00bz
- Join Date
- Jan 2006
- Location
- Shepherd, Michigan
- Age
- 38
- Posts
- 11,770
blacker than wesleysnipes- 98' trans am
hmmm i cant wait to replace mine
-
04-05-2008, 08:55 AM #25Member
- Join Date
- Aug 2007
- Location
- FLA
- Posts
- 249
Both a good price and a good bulb that wont burn out I had my replace twice on the right side of the car
-
04-05-2008, 03:25 PM #26Just me
- Join Date
- Nov 2006
- Location
- Broken Arrow, OK
- Age
- 51
- Posts
- 23,345
Pewter metallic- 2000 Camaro SS
I am doing some research on the 880s, 893s and 894s. All 3 of them have the same inside connection. The 880s are 27W, the 893s are 37.5W and I believe the 894s are 37.5W as well. The 893s should fit on the Camaro's fog lights like Getzen stated since the inside connection is the same.
The 893s have 1 exterior plastic fastener that runs north/south, while the 894s have 2 exterior plastic fasteners that are east/west side of the housing. I believe the 893s will work for the Camaro, you will probably not have any exterior fastener to hold the connector in place though. I plan to do a little more research as well.
-
07-08-2008, 09:02 PM #27Member
- Join Date
- Jan 2007
- Location
- Kerman
- Posts
- 158
Silver- 2002 Firebird Formula
how da heck do you get the other bulb out? from da socket
-
07-10-2008, 08:38 PM #28
auto zone carries all the star lites you need or they used to
-
07-11-2008, 02:25 PM #29
If you have a TA you will want to get it from the bottom. Take out the 3 plastic clips from the front bumper that bends underneth. Once you have them out pull it down a bit and you will see 2 10 mm bolts...remove them and pull the fog light down and at a bit of an angle (its a tight fit) unplug the bulb from the harness after you twist it counter clockwise and pull the tab back to slide the bulb out of the housing....the just reverse the directions for the install...DO NOT TOUCH THE BULB WITH YOUR FINGERS THE OIL WILL GET ON THE BULD AND POP AFTER IT HEATS UP.
-
07-13-2008, 12:39 PM #30Member
- Join Date
- Jul 2007
- Location
- Allen, TX
- Posts
- 411
Red- 2001 Trans Am
it is very hard to get from the top unless you have smaller hands. but if you turn the headlights on it does give you some more room.
Thread Information
Users Browsing this Thread
There are currently 1 users browsing this thread. (0 members and 1 guests)
Similar Threads
-
Rear Defrost light replacement?
By IZNUTHN in forum Stereo and ElectronicsReplies: 5Last Post: 10-27-2009, 03:51 PM -
Flip-up light replacement
By FirebirdFever in forum Firebird / WS6Replies: 25Last Post: 03-16-2009, 02:41 PM -
Replacement light bulbs...
By Z06-Goose in forum Appearance SectionReplies: 14Last Post: 07-04-2008, 05:36 AM -
Where to get replacement third brake light (99 TA)
By mockler in forum Appearance SectionReplies: 17Last Post: 04-05-2008, 03:16 PM -
Problem starting car after replacement a running light
By p1astik in forum General HelpReplies: 2Last Post: 06-22-2007, 03:44 AM



Reply With Quote


Bookmarks