Printable View
I was wondering if there is any problem with me running a 150 NX wet kit on my trans am. It is pretty much stock except for longtube headers, ory, loudmouth, slp lid, and smooth bellow. All the internals are stock. Have all necessary hardware for the install just wonderin if engine, tranny etc. can handle it :thinkin:
the engine and trans should deff. be able to take it, 150 is the highest shot that i've heard to be ok to run on a stock engine reliably. You are pushing it with the 150 wet, but it should handle it. Just my opinion, i know others will correct me if i am wrong
The engine should be able to handle it. I ran a 150 on mine for two years before my tranny died. I had an A4, didn't spray through the shifts.Quote:
Originally Posted by ws6man
Just make sure you have enough fuel, run all the safety devices and don't run lean.
i run a 200 motor rated (135 rwhp) on stock motor and fuel system. over a year now.
I agree with all the above....only thing I would consider is a 1 range cooler spark plug....
yeah i forgot to mention that. i run 2 steps colder plug. good catch. champion RC9YC
I would also recommend a fuel pump. I have seen a few cars lean out on a 150 wet. I would also recommend taking some timing out of it. I will be a safer way to run the 150shot. Just my .02
Ryan
Ok, thanks guys, i have ngk tr6 plugs already and im have access to ls1 edit to turn up the fuel etc. I have my own cable on ls1 edit because I bought it from a guy I know, so tuning is no problem. My Nitrous will turn on at 3000RPM and turn off during shifts. Im a newbie on this site and this was my first post ever, so thanks for the help!:drivin:
I believe the fuel pump issue is that the stock pump can't handle the demand for fuel. Thats why another fuel pump was recomended, at least thats why its recomended on the trucks.:dunno:
^^not enough fuel supplied for the demand=running lean.
i am thinking about nitrous on my car, but i'm a pussy and would only run a 100 shot i think, as long as i get up over 400 i'm happy! do you think you can spray thru the shifts with a 100 shot?
Remember its not HP that kills trannies. Its torque.
Some have gotten away with it. But plan on a rebuild.
how do you program it to not spray on the shifts? is it similar to a window switch or what do you have to use?
It IS using a window switch. You put in what "pills" you want the swtich to allow spray to begin and when to end. I think they come only in incriments of 200. Most people like to cut it off at 5800. You can also use a progressive controller.Quote:
Originally Posted by NE98LS1
-somebody
ok, i know how a window switch works, but when you are saying not spraying on the shifts, are you just talking about setting your window to below where your rpms fall on an upshift?
You stop spraying just before you shift.
manually? or is this done by a computer?
The window switch controls it. It fires the solenoids if Im not mistakes, it will fire them at lets say 3000 rpm then drop them out at 5800 or whatever your pills are set for so from 5800 till your shift point it wont be spraying, then when it shifts it will spray again.:drivin:
(This is how I understand it at least someone correct me if Im wrong)
Thats about right.
Hey about those msd window switches, the msd runs into a relay does the relay ground itself have to be provided? I am not sure if i am supposed to ground out the msd window switch and leave the ground out of the relay or ground both for it to work?
with a wto switch, it you let off to shift wouldent it cut off the n20. so a ws cutoff wouldent be needed
If you are talking about an A4, you would never lift.Quote:
Originally Posted by bad6as
On a M6, you really need a window switch. If you mis-shift, you will hit the rev limiter. The fuel will be cut, causing you to run lean.
doesn't the wot switch on a m6 keep you from spraying through shifts ? (as long as you don't pwr shift)
Yes, until you miss a shift.Quote:
Originally Posted by Danger731
if you miss your in big trouble coldfusion gave me a msd controler for $100. so its cheaper than a new engine
I have a 2000 ws6 procharged with 750's injecters, an an piston ran inline fuel pump, what kinda direct port shot would be safe to use runining 4 lbs and tunnign with the diablo. I need some help?