Printable View
asumeing everything is straight; will your rear end be aligned as long as both the LCA are the same length?
I'm asking because I shortened up my LCA before I put the bigger wheels on because the wheels were very close to the back of the wheel wells. I lowered the car and that's why it was like that.
the LCA are set to the same length on both sides so I just want to be sure I did it the right way
measure from the center of the front to rear wheel on each side and see if its the sameQuote:
Originally Posted by xmarkx
If you have adjustables your thrust angle could be off. I checked mine on an alignment rack just to be sure. If you want I could set that up for you. Don't think you will need it but-
I'm going to first do what tater is talking about but if it doesn't feel right I'll take you up on your offer C5. thanks guys
:thinkin:Quote:
Originally Posted by tatertot91
Don't forget the panhard bar.. Our cars favor the drivers side iirc.. In other words, I would check your latteral alignment too..Quote:
Originally Posted by xmarkx
what's another way I can check the PHB besides the "weight on a string" method. the wheels I have now slightly stick out of the fender so i'm not able to acurately tell anymore.Quote:
Originally Posted by Smittro
Only way I know of without equiptment..Quote:
Originally Posted by xmarkx
I threw my LCAs on my camaro and they were the same length but the car drove like it wanted to go one way when i had the wheel straight and was on the highway. Believe it or not did the measuring thing and the car drove straight as an arrow after that. But if your rear is pushed further towards one side it will throw the measurement off like smittro said. I didnt have much room for panhard alignment because the tires would have rubbed
If they stick out past the fender, you could just take a straight edge off the actual body of the car to the wheel on each side and see how close it is by eye-balling it.Quote:
Originally Posted by xmarkx
I've actualy done that already and it looks fine. I've adjusted the panhard twice before I adjusted the LCA and put big wheels on it was perfect then, so hopefuly measuring from the front wheels to the back will helpQuote:
Originally Posted by 35th-ANV-SS
I suggest :
use PHB to set side to side,use LCA to adjust the wheels in center of wheel well,
complete alignment ( be sure it includes setting the rear thrust line)( I suggest some where close + 0.07( different car like different setting)after all above then set TA angle
just my .02' Johnny
yep, my rearend is pushed more to the driver side...about 1-2inchs....with my wider TT2s its very noticeable nowQuote:
Originally Posted by Smittro
same here, i gotta move mine over a little. Its not any more than an inch but you can tellQuote:
Originally Posted by Blackbird-WS6
:werd: I could'nt remember which side..Quote:
Originally Posted by Blackbird-WS6
if you put wide rims you can tell EZ with the smaller ones its hard.....you will never have a problem :lol::lol:Quote:
Originally Posted by Smittro
:spank2::Poland::cheers::lmao:Quote:
Originally Posted by Blackbird-WS6
I measured like tater said and it's almost perfect so I'm going to leave it alone. I got the car on wheel ramps to adjust the TA and I notice the TA is pointed down in the bushing on the tranny side, so it looks like I'm going to have to drop the tranny support to adjust the placement.
I never thought lowering your car was such a PITA
true lol BUT it has nothing todo with the trans am.....its like this for all cars and trucks lolQuote:
Originally Posted by xmarkx
anytime you change something from factory setting you will pay the price :mad:
true...
Lowering your car changes the cars suspension geometry...therefore everything needs to be adjusted accordingly.
aka....bigger hammer :devil:Quote:
Originally Posted by 35th-ANV-SS