Results 1 to 7 of 7
Thread: rear end rebuild needed!!
-
08-24-2009, 10:04 AM #1
- Join Date
- May 2006
- Location
- roosendaal , netherlands
- Age
- 39
- Posts
- 189
white- 2000 transam ram air WS6
rear end rebuild needed!!
hey i am gonna rebuild my rearend but i also wanna put 4;10 gears in there!
What is the best place to purchase the entire kit to rebuild my rear end and what brand gears makes less noise richmond/slp/motive ??
do the 4;10 make a lot of difference over stock??
thanks for the replys
-
08-24-2009, 08:46 PM #2
Stop. Step away from the 10 bolt.
Look for a 12 bolt or 9". You'll love the 4.11, but not in your teeny 10 bolt.
Your going to rebuild it, then blow it again. Band-aid fix.
-
08-25-2009, 07:43 AM #3
- Join Date
- May 2006
- Location
- roosendaal , netherlands
- Age
- 39
- Posts
- 189
white- 2000 transam ram air WS6
i know the original rear end sucks but i don't take it to the track or nothing i have my car 5 years but i only drove it 10.000 miles a moser axle is gonna run me 2000 3000 dollars + shipping to the netherlands is gonna be very expensive !!! that's why i am thinking of rebuilding it but does a moser axle make a lot of noise to or you don't hear the at al ?? and do they break to??
thanks for the replys
greetings barry
-
08-25-2009, 08:01 AM #4
- Join Date
- May 2006
- Location
- roosendaal , netherlands
- Age
- 39
- Posts
- 189
white- 2000 transam ram air WS6
what is better a 12bolt or a 9inch for a manual transmission the 9inch is better right?? and what is the best place to order ??
greetings barry
-
08-25-2009, 10:28 AM #5
Well depends on what your going to do. Drag racing at the track 9inch, just for street use, 12 bolt. A 12 bolt is usually cheaper than a 9inch thats why I say it depends but yes most 6speed guys like the 9inch at the track.
-
08-25-2009, 12:05 PM #6
- Join Date
- Nov 1999
- Location
- over here...
- Age
- 45
- Posts
- 25,709
[]D [] []V[] []D- 1999 trans am
4.11's in your stock rear will end up blowing up far faster than the stock 3.42 gears...
a rear won't be noisey if it is properly set up and has the correct backlash... i'd never just toss in a rear that is complete from a company... i'd have my buddy make sure it is set to the best backlash i can get...
-
09-07-2009, 01:24 PM #7
My Moser makes a little more noise than stock. It's different tooth cut on the gear. Not noticable with a LM2 exhaust
Thread Information
Users Browsing this Thread
There are currently 1 users browsing this thread. (0 members and 1 guests)
Similar Threads
-
rear end rebuild
By jezzell88 in forum General HelpReplies: 25Last Post: 02-17-2012, 06:41 PM -
Help: Rear end rebuild
By 01NavyBlueSLPSS in forum Western MembersReplies: 0Last Post: 07-03-2011, 05:10 PM -
Rear end rebuild
By JayTA98 in forum DrivetrainReplies: 15Last Post: 11-26-2010, 05:35 AM -
Rear end rebuild
By Fred H. in forum DrivetrainReplies: 8Last Post: 05-09-2008, 07:49 AM
Bookmarks