Results 1 to 11 of 11
-
06-19-2007, 06:34 AM #1
3200 to 3600 stalls come in..Help Please..
Doing a stall real soon here. Trying to convince myself to go bigger than 3200 as everyone always says they wish they did. Any opinions between Vig and Yank? Also, how much more RPM does it take to get going with a 3600 than a 3200 stall. This will be a semi DD and will be doing HEADS/CAM a bit later. Currnet mods in sig along with SUBFRAME AND STRUT TOWER BRACE. Thanks in advance for your knowledge...
-
06-19-2007, 06:36 AM #2
Left out signature.
2002 SS #1811 A4/3.23
FACTORY OPTIONS: ALL
SLP LID; BELLOWS; KOOKS LT/HEADERS W/HIGH-FLOW CATTED Y; GMMG; TAYLOR-PRO 8MM WIRES; NGK PLUGS; BMR STRUT TOWER BRACE & FRAME CONNECTORS; K&N; SLP SS GRILLE; KEY FOBS; MATS & DECK MAT; DASH PLATE
MORE ON THE WAY.......
-
06-19-2007, 07:49 AM #3
- Join Date
- Aug 1999
- Location
- Arizona
- Posts
- 51,364
Black- 383 Procharged & N20 Vert
I think you would be happer with either, but if you are staying NA go with the Vig 3600
-
06-19-2007, 08:26 AM #4
- Join Date
- Aug 2005
- Location
- Pittsburgh
- Age
- 50
- Posts
- 413
Just got the Vig3600 because my fuddle clutch went bad. I must say it is a fine convertor and am definitely happy with it so far.
02 TA A4
408ci - 244/250/612/622 | PRC 237 heads | FTRA |100mm lid | FAST92/92 | Kooks 1 7/8 | Hooker CB | DMH Cutout | built trans | Yank4000 | 412 motorsports tuned | stock rear:judge:
08 TBSS - Borla CB
-
06-19-2007, 11:32 AM #5
I dont know anything about a 3200 but i have a vig 3600 and its great I love the way it drives.
-
06-19-2007, 05:31 PM #6
- Join Date
- Feb 2006
- Location
- Lisle, Illinois
- Posts
- 49
quicksilver metallic- 2002 trans am WS6
Both Yank and Vig are top notch companies, Vigs, from what I've heard and read flash higher, than their stated stall size. If you go Vig, you can try a 3200 stall first, cause they offer one free restall, then you could go to 3600 or bigger if 3200 wasn't enough.
I have a Yank ss3600 and love it. Hits hard, great drivibility as well. I would say 3600 since you plan on head/cam later on.
As far as the rpms, it won't be that much of a difference when taking off.
-
06-20-2007, 11:43 AM #7
Thanks for all the info. so far, much appreciated!! Any other thought or opinions would be excellent. Could anyone get specific how much more RPM it takes to get going. That is my biggest concern. Thanks again.
-
06-20-2007, 11:52 AM #8
- Join Date
- Mar 2007
- Location
- NC
- Posts
- 421
NBM- 1998Z28
Now the Vigalante is what I call a loose convertor. I have the 3200-3400 vig and I'm running a MS4 on the street with 3.73 gears and I love it. I have found out that the more you increase your hp adding/heads/cams/boltons the higher the convertor will stall. I just changed out the tranny for a new 700hp/4L60e and while it was down I sent the convertor back to Percision for a free restall/cleanout of the convertor. I could have had it restalled to any rpm I wanted but I just told them to clean her out and restall at 3200-3400 again. Because you've messed up if you burn up your tranny, buy a new one and stick your old stall back on there. It just dumps all that burnt fluid and clutch material back that stays in the old convertor. I can get out on the road and just give it enough gas to run 3000 rpm and let it walk thru the gears when I'm being carefull because of wet weather/ too many cops or I can stomp it and it will almost stall all the way to 4 grand melting the BFG 315s on the back. But you can crank it up and idleing at 800 it will pull the car around like it owns it. So if you crank it up and put it in gear without your foot on the gas it isn't gonna just sit there till you give it gas. Its gonna pull you around like it owns you. Which is excellent because you can lope around a low speed at the Sonic with your cutouts open and rattle everybody ride.
Last edited by PFM; 06-20-2007 at 12:02 PM. Reason: add
-
06-20-2007, 04:16 PM #9
4.10's MS3 and Vig 3600 here. Taking off easily i usually pull about 14-1500 rpm's to get moving and it usually shifts and hovers around 2000.
-
06-21-2007, 02:15 PM #10
-
06-27-2007, 06:58 PM #11
I notice you have a 2002 vehicle, you should consider replacing the weak flexplate with a TCI SF29 unit, both Jeg's and Summit sells them, you have to remove 3 of the 5 bolts anyway to replace the converter.
Either Yank or Vig is a good converter, however the latter is a 9 1/2" unit opposed to a 10 1/2" (Yank) so don't forget the tranny cooler.
SteveC
Thread Information
Users Browsing this Thread
There are currently 1 users browsing this thread. (0 members and 1 guests)
Similar Threads
-
Help: Car Stalls, jerks, goes..stalls
By Oldsmobileman in forum General HelpReplies: 5Last Post: 07-08-2016, 03:30 AM -
ls1 4l60e 3200-3600 stall wanted
By turbocreeper in forum Parts Wanted / TradeReplies: 0Last Post: 02-07-2011, 10:07 AM -
ebay stalls
By ls1wallen in forum Automatic TransmissionReplies: 4Last Post: 09-04-2010, 08:26 PM -
Help: T/A stalls out
By 02superfly in forum General HelpReplies: 21Last Post: 01-18-2009, 06:02 AM -
FAQ about stalls
By Y2KPewterSS in forum Automatic TransmissionReplies: 0Last Post: 09-19-2007, 08:22 PM
Bookmarks