Results 1 to 11 of 11
Thread: Replacing Turn signal bulb
-
08-09-2005, 02:02 PM #1
Replacing Turn signal bulb
My Left turn signal bulb burned out. I have the correct replacement bulb but I can not figure out how to turn the bulb housing. I did locate the bulb from inside the engine compartment. I know this must be a simple change since the Oil guy did it for me last time with no problems. Is there a simple description someone can give me to help? I want to avoid any tickets and living in Arizona in the summer I don't want to drive around with my window down in 100+ degree weather.
Any help would be great!
THANKS
-
08-09-2005, 02:07 PM #2
- Join Date
- Jul 2005
- Location
- Earth
- Age
- 47
- Posts
- 3,365
414 RWHP 395 RWTQ- 00 Black Ram Air Trans Am
I actually reach in through the open vent under the turn signal in the front of the car, twist the housing and pull it down and out of the vent. Be careful as it doesn't come all the way out. pull the old bulb and then replace the housing twisting it back in place.
-
08-09-2005, 02:09 PM #3
-
08-09-2005, 02:10 PM #4
Hurley711,
I'll have to go outside and try that... I don't remember seeing an open vent but then I was not looking for it.
Thanks! :beer3:
-
08-09-2005, 02:50 PM #5
Hurley711,
My car has fog lights below the turn signals.... do I remove those? I know the guy replaced them from going inside the engine area. I'll try again after work
-
08-09-2005, 03:04 PM #6
- Join Date
- Jul 2005
- Location
- Earth
- Age
- 47
- Posts
- 3,365
414 RWHP 395 RWTQ- 00 Black Ram Air Trans Am
Oops, I have a TA, my front is prob diff then you Camaro, just notcied now you have Camaro and not Firebird
-
08-09-2005, 04:59 PM #7
- Join Date
- Aug 2005
- Location
- Buda Tx South of Austin
- Age
- 49
- Posts
- 218
Artic White- 2000 SS Camaro M6
Right under the front of the car...you'll have 2 (if i remember right) bolts i think 10mm? take those off and the flap folds down. reach your hand in and .....walaaaa
-
08-09-2005, 07:38 PM #8
Keno2095,
Very Cool logo! Ok.. I will go and check for a flap. I did a short look first time one went out and did not really see an easy way. It would have been nice if the manual the car came with gave some hint of this process .... time to break down and get a REAL manual I guess. Off to check.....
-
08-09-2005, 08:03 PM #9
THANK YOU!!!!
saved from from taking it to someone and looking dumb. Now I have to seal that area so no water gets in. It does rain sometimes in AZ.
-
08-10-2005, 05:43 PM #10
- Join Date
- Aug 2005
- Location
- Buda Tx South of Austin
- Age
- 49
- Posts
- 218
Artic White- 2000 SS Camaro M6
NP ..i have to replace often...got a pinhole crack :-(
-
08-12-2005, 08:02 AM #11
- Join Date
- Aug 2005
- Location
- Anchorage, AK
- Posts
- 23
I believe you can drill a small hole in the bottom of the turn signal housing for water to drain out of and keep your bulbs from breaking. I haven't done it yet, but I'm pretty sure you just drill a tiny hole for the water to drain out of.
Thread Information
Users Browsing this Thread
There are currently 1 users browsing this thread. (0 members and 1 guests)
Similar Threads
-
Help: replacing turn signal bulb in a 97 camaro RS
By 01SOMSS! in forum Camaro / SSReplies: 6Last Post: 11-09-2008, 07:43 PM -
replacing turn signal bulb in a 97 camaro RS
By 01SOMSS! in forum Appearance SectionReplies: 2Last Post: 11-07-2008, 06:32 AM -
turn signal/drl bulb issue
By 1MileCrash in forum General HelpReplies: 11Last Post: 11-06-2008, 05:44 PM -
Turn Signal Bulb Install ?
By FireRescueWS6 in forum General HelpReplies: 2Last Post: 01-30-2008, 05:02 PM -
Replacing L front turn signal bulb
By Danger731 in forum General HelpReplies: 6Last Post: 10-19-2005, 11:25 AM
Bookmarks