Results 1 to 10 of 10
Thread: reassembly of top end help
-
03-14-2015, 07:47 AM #1Member
- Join Date
- Aug 2008
- Location
- Huron Ohio
- Posts
- 764
Black- 2000 WS6 Trans AM
reassembly of top end help
So I did the air and egr delete and my buddy's shop is gonna do the race headers but before I can put my fast 92 on I need to clear the egr on the passenger side. I can barely reach the bolts on the header because they are basically buried in there. Any tips?
98' Trans AM
RIP
00' WS6/Black/Pacesetter LT's/Magnaflow Exhaust/SLP lid/Nick Williams 92mm TB/FAST 92 Intake/BMR Strut Tower Brace/BMR Rear LCA's/BMR Panhard Bar
-
03-14-2015, 08:28 AM #2Veteran
- Join Date
- Feb 2009
- Location
- Mansfield, PA
- Posts
- 22,146
Black & Blue- '02 WS.6 / '07 Suburban
Our wasn't equipped with an EGR, so I am no help on this one. Sorry.
-
03-14-2015, 09:41 AM #3Member
- Join Date
- Aug 2008
- Location
- Huron Ohio
- Posts
- 764
Black- 2000 WS6 Trans AM
It's just so impossible to get to...would I hurt the car if I drive it 4 miles to where the headers are gonna get put on?
-
03-14-2015, 02:38 PM #4Spaz is My Mentor
- Join Date
- Feb 2009
- Location
- Florida Man Status Acheivement
- Posts
- 11,759
Navy Blue Metallic- 98 T/A w/ mods, 00 FBVert
delete the egr....
-
03-14-2015, 03:13 PM #5Veteran
- Join Date
- Feb 2009
- Location
- Mansfield, PA
- Posts
- 22,146
Black & Blue- '02 WS.6 / '07 Suburban
Got anything to plug it off with?
-
03-14-2015, 06:09 PM #6Member
- Join Date
- Aug 2008
- Location
- Huron Ohio
- Posts
- 764
Black- 2000 WS6 Trans AM
I'm trying to delete but the bolts on the lower part of the passenger header are impossible to get to...I might just tow it out there, the only thing I could use is a shop towel to plug it
-
03-14-2015, 06:41 PM #7Spaz is My Mentor
- Join Date
- Feb 2009
- Location
- Florida Man Status Acheivement
- Posts
- 11,759
Navy Blue Metallic- 98 T/A w/ mods, 00 FBVert
Try removing the coil packs and plug wires. EGR hose should come off and allow you to move out of the way.
-
03-15-2015, 10:11 AM #8Member
- Join Date
- Aug 2008
- Location
- Huron Ohio
- Posts
- 764
Black- 2000 WS6 Trans AM
I'll give that a try thanks
-
03-16-2015, 12:27 PM #9Member
- Join Date
- Aug 2008
- Location
- Huron Ohio
- Posts
- 764
Black- 2000 WS6 Trans AM
Also what size fernco are you guys running or suggest, tried the 3 inch and no matter how much I shaved off the inside it would not fit my nick williams 92. Thinking about just doing 4 inch what do you fellas think. By the way got everything installed and running the block of plates aren't on just sounds like it has a hole in the exhaust. I'll limp it to my buddy's garage shouldn't be an issue.
-
03-16-2015, 05:54 PM #10Veteran
- Join Date
- Feb 2009
- Location
- Mansfield, PA
- Posts
- 22,146
Black & Blue- '02 WS.6 / '07 Suburban
Still have the stock bellows here.
Reply With QuoteThread Information
Users Browsing this Thread
There are currently 1 users browsing this thread. (0 members and 1 guests)
Bookmarks