Results 1 to 8 of 8
-
03-15-2012, 07:01 AM #1
- Join Date
- Mar 2012
- Location
- strickland
- Posts
- 1
black- 98 zed soft top
hypertech pp3 vs. 3.73 gears ????
Hello, I'm a nubie on here and had some questions. I'm looking into my next mod and narrowed it down to a pp3 or 3.73 gears. I'm going for seat of pants feel and dont have enough funds for both. My car is 98' Z/28 vert. a4 my mods are: slp loudmouth,k&n fipk,all the free mods,18in ruff racing staggered fit wheels.It's not my daily driver only has 70,000kms. PP3 is around $470ish and gears are 250 plus install kit plus i have a friend who is a cert. mechanic who can install them for me. Prices are higher cause I'm from canada eh!
thanx
-
03-17-2012, 11:55 AM #2
-
03-17-2012, 12:48 PM #3
Heard the hypertech plays with timing, and can actually do more bad than good. Gears are where its at. Then tune it. The speedo will be off until then.
1998 Z28: Bolt-ons, Stage ? 4L60E. 250rwhp@6500Ft (R.I.P 5/1/2013)
1998 Mystic Teal Trans Am: Bone stock. (In process)
-
03-17-2012, 01:08 PM #4
-
03-19-2012, 11:29 AM #5
Gears. However, if you abuse the rear don't plan on it lasting too long. Best bet is to upgrade to an aftermarket rear and gears all in one shot. Although pricey, blowing up your stock rear once or twice will equal the cost of good replacement rear once you factor everything in.
-
03-19-2012, 09:48 PM #6
my vote is for neither.......both are what I would consider bad mods. Hpp3 leaves a lot to be desired on the tuning end when you can get a mail order tune from frost for $150. Shipping might be an obstacle but would probably still be cheaper than the hpp3 and you'd get a much better tune. Gears in the 10 bolt is almost exactly the same thing as flushing a few hundred dollars down the toilet. The 10 bolt won't last and eventually is going to puke those gears out.
I would do a set of headers.
-
03-24-2012, 11:56 PM #7
I did 3.73 gears with girdle. I haven't broke my stock gears yet. A lot of guys go to 4.11's but, I knew I was going to SC the car eventually so 3.73 were recommended. I picked up about .2 in the quarter and mid-range jump improved some. I'd do it again for th $325 it cost me back then. Probably closer to $600 now though for parts, install and set-up. I also bought the HPP3 and only used it for winter summer gas adjustments, gear/tire ratio adjustment and taking out speed limitter. I don't use that anymore since the SC went in and it was tuned with HPTuner.
-
03-25-2012, 09:53 AM #8
Thread Information
Users Browsing this Thread
There are currently 1 users browsing this thread. (0 members and 1 guests)
Similar Threads
-
Hypertech ?
By wooddaniel in forum Computer & TuningReplies: 11Last Post: 03-08-2010, 06:33 AM -
Help: about to change my plastic gears for brass gears
By edrvsqz1980 in forum General HelpReplies: 17Last Post: 07-18-2009, 05:09 PM -
Hypertech III 99-02 for sale/trade - gears, tower brace, headers, wheels
By chadnol10 in forum Parts For Sale / TradeReplies: 1Last Post: 01-17-2007, 03:50 PM -
Stock 2.83 gears to 3.73 gears?
By 97formula in forum Automatic TransmissionReplies: 3Last Post: 11-20-2005, 08:36 AM -
3:73 gears, 3:42 gears, clutch, flywheel, plug wires
By ls1hater in forum Parts For Sale / TradeReplies: 4Last Post: 08-16-2005, 06:15 PM
Bookmarks