Results 1 to 20 of 34
Thread: Dyno Results-320rwhp, Just Borla
-
06-05-2008, 04:37 PM #1
- Join Date
- May 2007
- Location
- Kinston, NC
- Age
- 37
- Posts
- 194
Sunset Orange Metallic- 2002 Pontiac Trans Am WS6
Dyno Results-320rwhp, Just Borla
I just got a call from Wayne's Dyno, before I got my headers, lid, y-pipe, and cutout put on I was putting down 320rwhp with just a Borla catback exhaust. I will have dyno sheets of before and after he puts the parts on.
Last edited by fbird777; 06-06-2008 at 12:22 AM.
-
06-05-2008, 04:44 PM #2
very nice. did you have it tuned? you might have a factory freak.
-
06-05-2008, 05:14 PM #3
-
06-05-2008, 10:10 PM #4
- Join Date
- Aug 2005
- Location
- Pittsburgh, PA
- Age
- 42
- Posts
- 21,720
My life is a- Ben Stiller movie.
unless it's all included, what's the point of dynoing the car before modding?
-
06-06-2008, 12:17 AM #5
- Join Date
- May 2007
- Location
- Kinston, NC
- Age
- 37
- Posts
- 194
Sunset Orange Metallic- 2002 Pontiac Trans Am WS6
Last edited by fbird777; 06-06-2008 at 12:20 AM.
-
06-06-2008, 04:02 AM #6
on 2000 ta non ram air made 341 hp and 352ft lbs of tq all i have is free mods lid magnaflow cat back and alum flywheel, that day my car was runing hot but i dont know what it would make now
-
06-06-2008, 06:29 AM #7
- Join Date
- Aug 2005
- Location
- Pittsburgh, PA
- Age
- 42
- Posts
- 21,720
My life is a- Ben Stiller movie.
here's mine after dyno tune-about 340 rounded up. I have all the same, no cut out though and i get 32mpg @ 85 hwy...eat my shit, prius!
Custom Car Emblems from third_shift|studios
Pittsburgh Car Detailing & Paint Protection from ts|s detailing
jaison tortorea
-
06-06-2008, 07:58 AM #8
- Join Date
- Apr 2008
- Location
- conroe tx
- Age
- 44
- Posts
- 497
maple red metallic- 2000 firebird formula
can anyone guess what numbers i should be makin?? i have a 2000 formula firebird with directflow lid, granatelli sensor, and free mods.
-
06-06-2008, 09:31 AM #9
-
06-06-2008, 09:34 AM #10
-
06-06-2008, 09:36 AM #11
-
06-06-2008, 11:00 AM #12
-
06-06-2008, 02:46 PM #13
-
06-07-2008, 06:53 AM #14
This is the dino sheet from my ws6 6spd. stock
http://i251.photobucket.com/albums/gg301/1stta/IMG.jpg
-
06-07-2008, 09:44 AM #15
to the op sounds like you have a pretty good starting base
-
06-08-2008, 10:04 AM #16
-
06-08-2008, 01:59 PM #17
ya I was happy. The guy that ran the car said i must have a factory freak. Then others doubt you when you say its stock. I bought the car with 8000 on the clock and I don't think the guy was one that would have done anything to it.
-
06-08-2008, 02:28 PM #18
^ does it have any kind of tuning or is it just pure factory settings? (as far as you know). maybe the guy did get a tune...
-
06-08-2008, 03:21 PM #19
As far as i know the car is completely stock. I have thought about trying to dig up the guys # and give him a call. (Just spoke to the previous owner about the car and the dino #s. He said it is completely stock, no tune, no mods!)
Last edited by 1st TA; 06-08-2008 at 03:39 PM. Reason: spoke to previous owner
-
06-08-2008, 06:23 PM #20
Dam thats some crazy numbers i thot my car was a factory freak, dyno stock 321hp 347tq wen stock, i think most of the 02 WS6's usualy dyno around 315-330hp 340-355tq. Got full-bolt on but no Cam and dyno with a Tune was 394hp 391tq dnt got the sheet but gona get a Cam soon and ill get the printout then, and post it.
Thread Information
Users Browsing this Thread
There are currently 1 users browsing this thread. (0 members and 1 guests)
Similar Threads
-
Question: Do these dyno results seem right?
By egldriver in forum Computer & TuningReplies: 8Last Post: 01-04-2016, 03:56 PM -
Dyno results
By REVNORR82 in forum Dyno InformationReplies: 9Last Post: 10-16-2010, 05:29 AM -
dyno day results
By 02Ls1Formula in forum Dyno InformationReplies: 8Last Post: 12-19-2007, 08:42 AM -
Dyno results
By bguns10 in forum Dyno InformationReplies: 6Last Post: 06-29-2007, 04:29 AM -
Dyno Results
By GaryZ06 in forum CorvetteReplies: 16Last Post: 02-17-2007, 06:52 AM
Bookmarks