Need 02 sensors

[pmolina0436]

ok...I was tunning my car some more over the week with my tunner..He said that one of the 02 sensors might be defective cause its slow in reading...So im going to get some new 02 sensors, im looking for both but i have LT headers..anyone know what kind and where i can find some sensors for my car..thanks..

Also is a certain brand recommended? and is it a 2 wire or 4 wire design ?

[boostcreep]

got mine from autozone about a month ago when I did my header install, cost about $40 each, Mine are bosch sensors. They are 4 wire (IIRC)

[pmolina0436]

got mine from autozone about a month ago when I did my header install, cost about $40 each, Mine are bosch sensors. They are 4 wire (IIRC)

were they long enough for long tube headers? and did you have to cut wire?

[boostcreep]

I got extensions with my headers, so yes
Seriously though they won't reach without extensions (well depends on header I guess) but more than likely yours either have extensions already or they were spliced in. Which if that is the case you will most likely have to do same with new ones.

[mark21742]

I spliced extra wire in my factory o2s, but I HIGHLY recomend buying the extensions.....they are cheap and plug right in.
if you look in(i think ) the computer section Frost and Orion gave out the bosch part number.....there again I think it is for a rear vette o2

[JoshieDoom]

c5 corvette bosch 02 sensor..

No extensions factory fit.

[thearborbarber]

Bosch 13111 O2 sensor and no extension is needed.

[JoshieDoom]

c5 corvette bosch 02 sensor..

No extensions factory fit.

Bosch 13111 O2 sensor and no extension is needed.

haha thanks I was lazy bro

[mark21742]

haha thanks I was lazy bro

lol me too

[qwkgto]

ok...I was tunning my car some more over the week with my tunner..He said that one of the 02 sensors might be defective cause its slow in reading...So im going to get some new 02 sensors, im looking for both but i have LT headers..anyone know what kind and where i can find some sensors for my car..thanks..

Also is a certain brand recommended? and is it a 2 wire or 4 wire design ?

yeap autozone $44 do you have a ls1 or ls2?mine is a ls2 i can get part number its a bosch sensor.same as factory unit.

[pmolina0436]

Bosch 13111 O2 sensor and no extension is needed.

so these dont require any wire cutting right?? are these it
http://cgi.ebay.com/ebaymotors/ws/eB...3AIT&viewitem=

???

I know when they installed my headers they did cut wire to fit the headers...So if i get these i dont need anything else right?? just take my old and in with the new...plug and play?? they come with that connecter at the end of the wire right?

[thearborbarber]

so these dont require any wire cutting right?? are these it
http://cgi.ebay.com/ebaymotors/ws/eB...3AIT&viewitem=

???

I know when they installed my headers they did cut wire to fit the headers...So if i get these i dont need anything else right?? just take my old and in with the new...plug and play??

You should be all to go with those. The cable doesn't look long enough though. This where I bought mine

http://store.summitracing.com/partde...5&autoview=sku

or

http://www.ws6project.com/user_stor/...7e69d6a04c71a8

[pmolina0436]

yeap autozone $44 do you have a ls1 or ls2?mine is a ls2 i can get part number its a bosch sensor.same as factory unit.

its an ls1...I went to an advance autoparts today but all they have is the universal ones that require wire cutting..Im going to check autozone 2marrow..

[pmolina0436]

You should be all to go with those. The cable doesn't look long enough though. This where I bought mine

http://store.summitracing.com/partde...5&autoview=sku

or

http://www.ws6project.com/user_stor/...7e69d6a04c71a8

oh yea...the ones from summit look good.. That includes everything right..Like the connector at the end of the wire?
casue it says

Oxygen Sensor Bung Included: No <<<<<< dont know what that , means though?

[thearborbarber]

oh yea...the ones from summit look good.. That includes everything right..Like the connector at the end of the wire?
casue it says

Oxygen Sensor Bung Included: No <<<<<< dont know what that , means though?

Summit is where I got mine and they were plug and play. No splicing or cutting. The bung is the fitting that the sensor threads into.

[qwkgto]

its an ls1...I went to an advance autoparts today but all they have is the universal ones that require wire cutting..Im going to check autozone 2marrow..

the ls1s look alil diffrent autozone has toi order mine they are 4 wire on the ls2,in the fronts and rears,still cheaper then summit and no shipping charges,the ones I have are the exact fit as the factory ls2 02 units.ill have to remember to look at part number on box in the garage and post it up here.

[pmolina0436]

the ls1s look alil diffrent autozone has toi order mine they are 4 wire on the ls2,in the fronts and rears,still cheaper then summit and no shipping charges,the ones I have are the exact fit as the factory ls2 02 units.ill have to remember to look at part number on box in the garage and post it up here.

ok...I noticed that you said "front and rears"... Do i need to get 4 02 sensors..I thought it was only 2..??

[mark21742]

ok...I noticed that you said "front and rears"... Do i need to get 4 02 sensors..I thought it was only 2..??

get the rear o2s for a vette and use them in place of your front o2s, then just leave your rear o2s unhooked (delete them) stock you have 4, you will only be using your front 2 now

[cammed goat]

http://shop.ebay.com/?_from=R40&_trk...All-Categories

I'm going this route for these:
http://i10.photobucket.com/albums/a1...6/SDC10339.jpg

[pmolina0436]

get the rear o2s for a vette and use them in place of your front o2s, then just leave your rear o2s unhooked (delete them) stock you have 4, you will only be using your front 2 now

lol...oh yea i forgot that i deleted the other 2...Yea well im just going to get the front 02 sensors...thanks..