vengence racing cam ?

**Too Fast** · 07-13-2010, 05:37 AM

Just found this thread, kinda nice to read one where the project was started and then mostly finished. I LOLd at some of your frustrations, been there/done that!

**WS6S** · 07-13-2010, 01:08 PM

Originally Posted by Too Fast

Just found this thread, kinda nice to read one where the project was started and then mostly finished. I LOLd at some of your frustrations, been there/done that!

the end results were worth all the whining and crying

**WS6S** · 07-13-2010, 02:45 PM

here is the car after we put the dmh cutout on her.

[ame]http://www.youtube.com/watch?v=yOGYae6Lx7U[/ame]

**tatertot91** · 07-13-2010, 07:45 PM

Sounds mean!

**Z28boy2000** · 07-13-2010, 08:48 PM

sounds so damn good!

**Too Fast** · 07-14-2010, 03:59 AM

Is that a single cut out? Where on the I-pipe, just before the axle? Sounds mean as hell open.

**WS6S** · 07-14-2010, 06:10 AM

Originally Posted by Too Fast

Is that a single cut out? Where on the I-pipe, just before the axle? Sounds mean as hell open.

between the y and the tails.yes single cutout,made by dmh.really really high quality stuff.

**MudStainKILLA** · 07-14-2010, 06:23 PM

Originally Posted by WS6S

def nice!!!

**WS6S** · 07-17-2010, 02:03 PM

now if my son would stop using the car so i could drive it a little !!!

**MudStainKILLA** · 07-22-2010, 09:34 AM

lol but in the mean time u get to tool your cuda around!

**WS6S** · 07-23-2010, 02:51 AM

Originally Posted by MudStainKILLA

lol but in the mean time u get to tool your cuda around!

to friggin hot to drive that thing.

**MudStainKILLA** · 07-23-2010, 11:45 AM

i imagine georgia feels like the surface of the sun this time of year

**Lunatikgixxer** · 07-23-2010, 01:18 PM

sounds good man. what was the cam specs again? And what other sup mods did u do also? just curious..

**WS6S** · 07-23-2010, 04:38 PM

Originally Posted by MudStainKILLA

i imagine georgia feels like the surface of the sun this time of year

its friggin unreal,so are my power bills !

**WS6S** · 07-23-2010, 04:50 PM

Originally Posted by Lunatikgixxer

sounds good man. what was the cam specs again? And what other sup mods did u do also? just curious..

236/238 .601/.605 113 LSA ,tea dual gold .650"lift springs,melling hv oil pump,hardened push rods,ls2 chain,comp lifters,ls6 intake,mid length headers,gutted cats,ory,electric exhaust dump,magnaflow exhaust...i also put a luk #04-905 ls7 clutch setup in her as well as a set of 4.10,s.when i bought the car it already had a full spohn suspension and weld in connectors as well as a few other mods.oh ya i also stripped her naked and gave her a fresh coat of paint.

**WS6S** · 07-23-2010, 04:52 PM

im heading up to vengenance racing tomorrow morning to final tune and dyno her.

**Lunatikgixxer** · 07-23-2010, 05:29 PM

sweet man thats a nice cam

**MudStainKILLA** · 07-24-2010, 12:26 AM

looking foward to your dyno numbers

**qwk93ta** · 07-30-2010, 07:46 AM

I'd like to see some dyno numbers too. I have a new 6.0 motor with a torquer v2 cam, kooks and all bolt-ons. I don't have a dyno tune yet should be getting 3.73s very soon and then the tune. Here is a clip of my car:

http://s229.photobucket.com/albums/e...WS660motor.mp4

**WS6S** · 07-30-2010, 08:47 AM

Originally Posted by qwk93ta

I'd like to see some dyno numbers too. I have a new 6.0 motor with a torquer v2 cam, kooks and all bolt-ons. I don't have a dyno tune yet should be getting 3.73s very soon and then the tune. Here is a clip of my car:

http://s229.photobucket.com/albums/e...WS660motor.mp4

well some issues with my car at the dyno so my numbers were low.375 hp / 360 torque.it should really be around 400 /375 ish.i was only getting around 75% throttle travel.if i had an aluminum flywheel and long tubes i woulda been around 420 on hp