Results 1 to 17 of 17
Thread: Expectaions...........
-
10-05-2009, 08:25 PM #1
Expectaions...........
All right boys here is a list of goodies going on the TA in the next couple of weeks. Need to know If I'm missing anything,or would consider changing anything, and what you think the outcome might be..perhaps est. HP/TRQ, Time, etc.
AS IT SITS NOW...
1999 ws6 TA
6-speed
Lid
Shurflo Cat-Back only
BMR lowering complete setup, Panhard, Springs, Relocated
Control Arms, Subframe connectors, UMI Relocated Tunnel brace Tork Arm, Drag Bags, AGX Adj. all 4, Stock 10-bolt Rear-end.
Stock Drive Shaft
TNT 100-shot (special occassions only)
Ugrades......
LS6 intake from stock LS1
Ported TB Stock LS6
Ported 241 Casting LS1 heads w/ARP bolts
Comp Springs upgrade spring rate 313lb, Titanium retainers
Comp 7955 push rods
Pacesetter Long Tubes-ORY pipe keeping same Shurflo. CATLESS
224/224-.531- 112 lsa Cam
Ported LS oil pump
SPEC stage 2, upgrade lighter FW (not alum)
Stock bottom end
Drag Radials- not sure which yet. M&H or MT's
Stock size front tires for now 17's
Dyno and Tuned will be done by XXX motorsports Pensacola, FL
So Lets Here It...Let me know if I forgot to list any info needed.
-
10-05-2009, 08:34 PM #2
- Join Date
- Oct 2008
- Location
- Coral Springs, Fl
- Posts
- 5,774
Sunset Orange Metalic- 2001 Camaro SS
get some LCAs and relocation brackets
-
10-05-2009, 08:37 PM #3
Already done, listed in as it sits list.
-
10-05-2009, 08:41 PM #4
-
10-06-2009, 07:36 PM #5
-
10-06-2009, 07:41 PM #6
-
10-06-2009, 07:47 PM #7
mill those heads 59cc easy hp before you put it together.
-
10-06-2009, 07:49 PM #8
-
10-06-2009, 07:51 PM #9
c5z28 mill those heads 59cc easy hp before you put it together
Glad you bought that up. If I do mill heads which I have considered, how much before I have to change the rod lengths from stock length.. .30/.40 thnds?Last edited by Fastdaddy; 10-06-2009 at 08:25 PM.
-
10-06-2009, 07:52 PM #10
-
10-06-2009, 08:24 PM #11
Here's a good point.........
Here's the deal I got....
LS6 intake with Ported TB
Ported LS heads
TR 224/224- 112 cam
Ported LS6 oil pump
Pacesetters LT's ceramic
Comp rods
LS2 chain set- New
Comp springs/titan. retainers
All this came off of a 2002 SS with around 50K, with about 30K on these parts.
$1300.00 ( DEAL? ) I Think SO.......
Could you not pass this up?? It makes getting a rear end feel so much cheaper....
-
10-06-2009, 08:37 PM #12
That I couldn't tell you, There is a formula( I don't know it), but even then when I started asking people told me I still needed a pushrod length checker after everything was installed. Call texas speed or another aftermarket company they would be more specific than me.
-
10-06-2009, 08:41 PM #13
-
10-06-2009, 08:45 PM #14
-
10-06-2009, 08:50 PM #15
-
10-06-2009, 08:54 PM #16
-
10-06-2009, 08:56 PM #17
Thread Information
Users Browsing this Thread
There are currently 1 users browsing this thread. (0 members and 1 guests)
Bookmarks