Tab Content
  • SMWS6TA's Avatar
    Yesterday, 08:09 PM
    No I put it on the inside of the door, like the outside skin of the door panel. I removed the moisture plastic and reached in and pressed it on. I also did this to the speaker cubby holes on the sail panel too.
    11 replies | 219 view(s)
  • SMWS6TA's Avatar
    Yesterday, 01:30 PM
    It has it, row 4, column 9 You'll see Formula package on all Trans Am's
    28 replies | 274 view(s)
  • SMWS6TA's Avatar
    Yesterday, 01:12 PM
    It comes off the exhaust manifolds into a y pipe that goes into the muffler as a single inlet tube. Here you can have a muffler that continues as a single outlet or splits it into 2 outlets that then go to the tip. If a car has true duel exhaust it is an aftermarket system.
    28 replies | 274 view(s)
  • SMWS6TA's Avatar
    Yesterday, 12:51 PM
    When they came from the factory the 98's WS6's had single exhaust while the following years they came with dual. Over time many ppl have made them dual pipes. If you were trying to keep it in pure stock form then it should be with a single outlet.
    28 replies | 274 view(s)
  • SMWS6TA's Avatar
    Yesterday, 11:36 AM
    just add salsa.
    3782 replies | 135575 view(s)
  • SMWS6TA's Avatar
    Yesterday, 11:21 AM
    SMWS6TA replied to a thread mystery oil leak in General Help
    Will is currently trying to get his K member back in, I asked him to pop in here and give you some pointers.
    26 replies | 386 view(s)
  • SMWS6TA's Avatar
    Yesterday, 10:15 AM
    I'll add if you go the non-boost route you can always do a Speed Density tune like I did. Makes tuning a hell of a lot easier. :D
    28 replies | 274 view(s)
  • SMWS6TA's Avatar
    Yesterday, 10:09 AM
    Look like one. The paint chips are kinda expected with a 20 yr old car. You don't want to see mine. Seems decent price, 4th Gens have been coming up in price a little lately. Price could also be how much demand in your area they have. 9 yrs ago I got mine for $6500 USD but it was a...
    28 replies | 274 view(s)
  • SMWS6TA's Avatar
    Yesterday, 07:05 AM
    Here are 2 threads that can help you on your purchase. http://www.ls1.com/forums/f6/guide-buying-fbody-118628/ http://www.ls1.com/forums/f6/differences-between-f-body-years-27512/
    28 replies | 274 view(s)
  • SMWS6TA's Avatar
    Yesterday, 07:03 AM
    Ask him for the RPO code sheet. Located on drivers door. It should have WS6 listed. If not then it's not a real WS6. Filler panel could have had the paint faded over the years, but there should be an outline in the plastic. most ppl get a vinyl graphic to replace it. GM has greatly...
    28 replies | 274 view(s)
  • SMWS6TA's Avatar
    Yesterday, 06:00 AM
    I guess I didn't take any of the hatch area. I do remember laying some across the back and in the fender wells. I didn't lay any on the floor pan of the t top area or the back panel where the lights mount. Figure I didn't need it there. I ran out of material to put any on the hatch itself. I...
    11 replies | 219 view(s)
  • SMWS6TA's Avatar
    Yesterday, 05:44 AM
    I can think Obama for destroying the Etiquette of not shit canning your countries policies or rep when on foreign soil, so I can't be to upset about his stupidity of what he said yesterday's press conference. But come on......
    2602 replies | 36106 view(s)
  • SMWS6TA's Avatar
    Yesterday, 05:41 AM
    Stupid ppl vote in stupid ppl.
    22 replies | 428 view(s)
  • SMWS6TA's Avatar
    Yesterday, 05:40 AM
    I use Waze all the time. It's as real time as it could get as long as the users update those things.
    70 replies | 1297 view(s)
  • pajeff02's Avatar
    Yesterday, 03:06 AM
    pajeff02 replied to a thread mystery oil leak in General Help
    Yes. You need it up in the air. The cradle can be dropped and slid out of the way if everything is disconnected. In a nutshell that would be the front wheels, lower ball joints, lower strut mounts, steering coupler, P/S hoses, motor mounts, any wire harness connectors (such as ABS), and the four...
    26 replies | 386 view(s)
  • pajeff02's Avatar
    Yesterday, 03:01 AM
    ^^ Amen on that one. You and Spaz are definitely brothers from another mother.
    28 replies | 274 view(s)
  • pajeff02's Avatar
    Yesterday, 03:00 AM
    :D Made it home around 10:30 last night. We left for Detroit a bit early in case of traffic or other issues. For us, "other issues" turned out to be driving rains and an accident on I-96 that re-routed us. My brother uses Waze as the navigator on his phone and I was impressed with how it...
    70 replies | 1297 view(s)
  • KahanaReef's Avatar
    07-16-2018, 08:45 PM
    I truly don't understand how these lunatic CA Dems keep getting voted into office. Seriously, it's got to be voter fraud flat out because nobody is that stupid.
    22 replies | 428 view(s)
  • SMWS6TA's Avatar
    07-16-2018, 04:08 PM
    Those two working together......
    1451 replies | 10773 view(s)
  • SMWS6TA's Avatar
    07-16-2018, 04:02 PM
    No one can say I do half ass shit when breaking something :chuckles:
    28 replies | 274 view(s)
  • SMWS6TA's Avatar
    07-16-2018, 03:59 PM
    Ed Love the avatar. If you don't plan on doing heavy mods like I have then the WS6 is good to go. If you plan on doing what I did then a non-WS6 (slick beak) bird is better and cheaper most of the time. I upgraded everything that made a WS6 for better parts so it would have been a waste of $$$...
    28 replies | 274 view(s)
  • SMWS6TA's Avatar
    07-16-2018, 03:56 PM
    Mine was my fault. Doing a burn out and missed the line lock release and hit the rev limiter twice. It grenade in spectacular fashion. Wiped 3-5 main bearings, spun 5-8 rods, something to this day I can't identify destroyed piston 7 & 8 bottom skirt and blew a hole along the oil galley by #4...
    28 replies | 274 view(s)
  • SMWS6TA's Avatar
    07-16-2018, 10:05 AM
    SMWS6TA replied to a thread slave adjusting in Drivetrain
    neither did my LS7 clutch kit.
    3 replies | 65 view(s)
  • SMWS6TA's Avatar
    07-16-2018, 10:04 AM
    Another member of the 98 club here too. Biggest worry on the 98's is the oil pump. 97-98 oil pumps don't like high rpms (above 6k) especially with high miles. Believe me I know this, it may or may not be the reason I have a 403 in mine now :whistle: If you do get it, a good mild...
    28 replies | 274 view(s)
  • SMWS6TA's Avatar
    07-16-2018, 08:16 AM
    Made Breakfast Jambalaya Sunday. Hash browns, Bell Peppers, Onions, Scramble Eggs, 2 types of Sausage, and Ham chunks all mixed together. :yum:
    3782 replies | 135575 view(s)
  • SMWS6TA's Avatar
    07-16-2018, 08:11 AM
    SMWS6TA replied to a thread slave adjusting in Drivetrain
    The fingers should touch the slave a little. Not enough that they're pressing in more than an 1/8". Shims are mostly used to bring the slave closer to the fingers because of the aftermarket bell housings or clutch kits are slightly different then OEM depths. I have a QuickTime SFO BH and...
    3 replies | 65 view(s)
  • SMWS6TA's Avatar
    07-16-2018, 08:05 AM
    SMWS6TA replied to a thread Help: 2002 m6 hydrulics wont bleed in Drivetrain
    Sorry I didn't respond I was out fishing most of the weekend.
    3 replies | 85 view(s)
  • SMWS6TA's Avatar
    07-16-2018, 07:41 AM
    SMWS6TA replied to a thread mystery oil leak in General Help
    Yes you'll need to raise it up enough to be able to maneuver around under there. No. Jeff came up with a method of supporting the engine while dropping the K member. hopefully he can post a pic
    26 replies | 386 view(s)
  • SMWS6TA's Avatar
    07-16-2018, 06:11 AM
    Ordered the Vert's new top from Rockauto. I like their prices but the waiting is a PITA sometimes. A week before it ships?!?! I also priced my drag wheels for the front. I'm placing my order next month hopefully :D
    6189 replies | 627760 view(s)
More Activity

9 Visitor Messages

  1. View Conversation
    I believe photoshop can help you with that lol
  2. View Conversation
    yeah i wasn't too happy about the price but that's the only place I can find it. Yeah fuel pumps are not fun. I tried lowering the tank for a couple of hours and the neck wouldn't clear. I have the metal tank. As much I didn't want to do it , I did the trap door. I'm glad i did. It takes about 20 mins to swap a pump out now. Did it just went bad or upgrading? Good luck with yours.
  3. View Conversation
    hey did you find out about the mobil one engine plate? I got it off ebay. Is about $25.
  4. View Conversation
    What is the deal with the Tech Team icon?
  5. View Conversation
    congrats
  6. View Conversation
    Congrats!
  7. View Conversation
    Header bolts..I got them for Summit..Percy's Split Lock Friction Lock header bolts...PHP-21008 is the summit part##..Stainless Steel, Polished, Set of 12 for $60
  8. View Conversation
    You can probably find the Mobil 1 plaque at Afterthoughts, GMpartsdirect or egay. Stealerships might still have them as well.
  9. View Conversation
    online tires, have your local tire shop that you trust price match so you don't pay shipping.
    Can't post in forum or i'll get an infraction
Showing Visitor Messages 1 to 9 of 9
About sjsingle1

Basic Information

About sjsingle1
Color of Car:
silver
Year & Model Car:
2000 formula
Location:
texas
Occupation:
computer tech

Statistics


Total Posts
Total Posts
1,621
Posts Per Day
0.52
Last Post
Fuel Pump - Granatelli or Racetronix? 09-29-2013 12:05 PM
Albums
Total Albums
1
Total Photos
4
Visitor Messages
Total Messages
9
Most Recent Message
06-27-2011 02:41 PM
General Information
Last Activity
12-29-2016 04:01 PM
Join Date
01-21-2010
Referrals
0

8 Friends

  1. fbodyNATION fbodyNATION is offline

    **Te@M fBoDy**

    fbodyNATION
  2. JayTA98 JayTA98 is offline

    Senior Member

    JayTA98
  3. jonnyman jonnyman is offline

    Member

    jonnyman
  4. KahanaReef KahanaReef is offline

    She Moderator

    KahanaReef
  5. KMdef9 KMdef9 is offline

    Electrical Engineer

    • Send a message via AIM to KMdef9
    KMdef9
  6. pajeff02 pajeff02 is offline

    Super Moderator

    pajeff02
  7. SexOnWheels SexOnWheels is offline

    Paid 2 Post Daycrew

    SexOnWheels
  8. SMWS6TA SMWS6TA is offline

    Spaz is My Mentor

    SMWS6TA
Showing Friends 1 to 8 of 8
iTrader Profile Recent Ratings
iTrader:
Positive Feedback:
0
0%
Members who left positive:
Members who left negative:
0
0
Total positive feedback: 0
Submit Feedback For sjsingle1
View Complete Feedbacks for sjsingle1
  Past
Month
Past
6 Months
Past
12 Months
  0 0 0
  0 0 0
  0 0 0