Results 1 to 5 of 5
  1. #1
    Blown, Stroked, & Sprayed

    Ed Blown Vert's Avatar
    Join Date
    Aug 1999
    Location
    Arizona
    Posts
    51,361

    Black
    383 Procharged & N20 Vert

    PE Added = No Effect

    Was on the dyno checking AFR. At 4000 it was 12:1 so added 5% to the PE table @ 4000. No change in AFR. Then added another 10% then 15%. Still no change. Everywhere else I had no problem changing the AFR.

    What am I missing?
    Black 1999 Blown Convertible A4
    Forged 383 | ATI D-1SC
    NX MAF Kit | 222/226 .585 115
    AS Stage II 6.0L FI Heads
    Moser 9" | 3.70 | Wavetrac | 35 Spline | Vigilante 3600
    548.0 RWHP - 563.8 RWTQ - 10# - D1

    666.0 RWHP - 734.2 RWTQ - 125 Shot - P1

    Black 2009 Escalade Hybrid 4WD



  2. #2
    Grand Imperial Wizard Sarge's Avatar
    Join Date
    Aug 2005
    Location
    Texas Department of Corrections
    Posts
    18,128
    Retired Outlaw Sum Bitch

    In open loop.....I assume....are the O2 sensors preventing the change for some reason?

  3. #3
    Junior Member MNR-0's Avatar
    Join Date
    Aug 2005
    Location
    Australia
    Age
    55
    Posts
    79

    BLACK
    2004 Monaro

    Ed,

    Monitor your "Fuel Air Multiplier" and "Air Fuel Ratio Commanded Hi Res" PIDS during a WOT run. Check what value the VCM is commanding at WOT. If it is something different to what you are commanding via your PE table then look into your program for that Open Loop AFR value.

    It can only come from 5 places at WOT:

    PE
    PE Add vs ECT
    PE Add vs IAT
    OL F/A
    COT

    My guess it is COT, or CAT protection. Have you disabled it yet? If not, CAT protection will override the PE value.

    Another thing you might try is turn off the LTFTs. Fuel dumping at WOT is difficult to control when LTFTs give you the run around.

  4. #4
    Blown, Stroked, & Sprayed

    Ed Blown Vert's Avatar
    Join Date
    Aug 1999
    Location
    Arizona
    Posts
    51,361

    Black
    383 Procharged & N20 Vert

    COT was turned off.

    Your probably right on the OLFA. I just remembered that on a few pulls on the dyno. My AFR dropped to over 10:1 That must have been when it was using the PE table.

    I never touched the OLFA table, how does it work??

  5. #5
    Junior Member MNR-0's Avatar
    Join Date
    Aug 2005
    Location
    Australia
    Age
    55
    Posts
    79

    BLACK
    2004 Monaro

    You really need to log your "Commanded AFR" PIDS as above to determine exactly what is happening. The OLFA table is used for part throttle (non WOT) in place of closed loopwhen closed loop is disabled. At WOT, you are still running open loop, so the VCM will take the richer of the 2 values (PE vs. OLFA) and use that.

    What are your LTFTs doing at WOT? I recommend disabling them for all the trouble they are worth. Your car will still run fine switching off the STFTs and since you have HPT you can still dial in the fuel trims off that - infact - thats how I always do it.

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. Mass Effect 2.....
    By Superluminal in forum Almost Anything Goes
    Replies: 3
    Last Post: 02-15-2010, 07:54 AM
  2. Cause and effect. It is about to be finished!!
    By knappbunch in forum Camaro / SS
    Replies: 11
    Last Post: 11-13-2008, 12:00 PM
  3. Mass Effect (360)
    By Soltakr in forum Computers / Gaming
    Replies: 7
    Last Post: 06-05-2008, 04:13 PM
  4. mass effect 360
    By ls1bandit in forum General Classifieds
    Replies: 0
    Last Post: 01-18-2008, 07:10 PM
  5. What Ground effect is this ?
    By RamairWS9 in forum Firebird / WS6
    Replies: 28
    Last Post: 01-08-2008, 01:16 PM

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •