Results 1 to 15 of 15
Thread: What series u-joint help
-
05-18-2009, 08:53 PM #1
What series u-joint help
What series u- joint is stock installing my 9 inch and the builder said it a 1330 so I got a 1330 yoke it's longer than a 1350 so the driveshaft is in the tailshaft properly and length is ok but the u joint cap won't fit right they sit on top of the notch in the yoke where it suppose to be between to hold the caps on hope you understand please help
-
05-19-2009, 07:27 AM #2
Who's weiner do I have to play with to get a responds from around here. PS I will not play with your weiner don't ask.
-
05-22-2009, 06:31 AM #3
-
05-22-2009, 08:01 AM #4
I can maybe get pic this weekend but what series u- joint is factory 1310 or 1330 or something different. There is notchs so
When the u joint rest in the yoke the caps of the u joint stay in place but my joint hits this notchs so it would be unsafe to drive
-
05-22-2009, 01:15 PM #5
The factory uses; Saginaw 44. Also called S44, Saginaw, 3R. It's real close to a 1330 and believe they are interchangeable but you had better take measurements of u-joint first.
-
05-23-2009, 02:04 AM #6
-
05-23-2009, 06:54 PM #7
Napa has conversion u-joint to convert from one to another.
-
05-23-2009, 07:23 PM #8
I got an alum drive shaft with a 1350 conversion already on it for sale. came off a 6spd 99 ws6 with a moser 9" rearend. 150+ship
-
05-23-2009, 09:45 PM #9
where you at in illinois
-
05-23-2009, 09:51 PM #10
now have a issue with the wheels fitting they are hitting the inner fenders/wheel well both sides i have the zr1 wheels i think the wheels are to wide my 9 inch project has been a nitemare first u -joint wouldnt fit got it to fit today a little grinding and smoothing out fit fine now measured the 10 bolt and measure the houseing and are the same length do not know why it wont fit. starting to go crazy. started to break in the rear with it on jack stands and the rear is kind of howling so i just going fuckin nuts please help anyone
-
05-24-2009, 11:52 AM #11
- Join Date
- Dec 2005
- Location
- Laurel, Maryland
- Posts
- 4,975
2000 Grand Prix GTP- 2000 Trans Am WS6 M6
Adjustable Panhard Rod.
http://www.ls1.com/forums/showpost.p...7&postcount=13
-
05-24-2009, 02:40 PM #12
half hour west of chicago.
-
05-24-2009, 08:31 PM #13
i have a adjustable panhard rod but both wheels are hitting i dont think i can adjust that when both sides are hitting maybe i need more info i have the zr1 wheels and there pretty wide with a 315 tire need help please and thank you
-
05-25-2009, 06:34 PM #14
-
05-25-2009, 09:17 PM #15
Well I guess I will just remove the bump stops. Just a little cut off wheel and a BFH mite work I didn't. Know I had to remove the bump stops
Thread Information
Users Browsing this Thread
There are currently 1 users browsing this thread. (0 members and 1 guests)
Similar Threads
-
u joint help
By SilverBulletLS1 in forum DrivetrainReplies: 4Last Post: 01-16-2014, 07:06 AM -
So tell me about my u-joint
By goof4080 in forum DrivetrainReplies: 3Last Post: 07-03-2012, 03:44 PM -
Question: u joint??
By Karczewski in forum General HelpReplies: 4Last Post: 10-26-2011, 09:22 AM -
Question: Bad u-joint???
By joedude02 in forum General HelpReplies: 2Last Post: 11-02-2008, 09:09 PM -
U-Joint
By 01CalgarySS in forum DrivetrainReplies: 3Last Post: 09-18-2008, 05:43 PM
Bookmarks