Results 1 to 5 of 5
Thread: u joint help
-
12-22-2013, 06:04 PM #1
- Join Date
- Nov 2013
- Location
- Miami, FL
- Posts
- 15
Pewter- 2000 Trans AM
u joint help
o my u joint busted today.. a little confused on which U joint to get because I have a moser 12 bolt on my 2000 T/a so if I go to autozone and ask for a U joint for my 2000 T/a will it fit the moser 12 bolt or do I have to get a different size? hope you guys understand what I am trying to ask.
-
12-24-2013, 04:09 PM #2
- Join Date
- Jan 2009
- Location
- North Jersey
- Posts
- 11,496
Phantom Black Metallic- 2004 GTO M6
u joint help
If you haven't already, take the driveshaft out and take it to a driveshaft shop so they can match up your u-joint to the replacement. Have the balance checked as well while the shaft is there.
extreme dimensions, driveshaft shop, harrop, hid(35watt/6k) lows, hurst, k&n, led fogs, maverick man, mishimoto, nitto, revshift, slp, stern st-1, smoked sidemarkers, whiteline poly radius rod bushings
-
12-25-2013, 10:16 AM #3
Most likely you have a 1350 series u-joint -- if the driveshaft was also upgraded along with the rear. If not, it is possible that you have a combo u-joint that runs different size caps. This should help you determine what you have: U-Joint series identification
-
12-27-2013, 10:37 PM #4
My advice would be to call the place your got your rear end and driveshaft from. They will answer this spot on.
2000 Trans Am T56 Swapped - GMPP "HOT" Cam | LS6 Intake | PnP TB | 25% UD Pulley | Founders adjustable LCA/PHB/TA | Norris Catch Can | TSP 1-7/8 SS LT | TSP True Duals with bullets | SLP Lid | UMI Shock tower brace | Torq Thrust M 17x9 275/40 front 17x10.5 315/35 rear - YouTube Videos - My Car Site
-
01-16-2014, 07:06 AM #5
IF, when you got the moser 12 bolt you didn't change the shaft then you should have a 2-1153 joint from neapco
IF, you did change the shaft when you went to the moser 12 blt then you should have a 5-178x or 5-1350x joint from spicer.
IF, half the joint has inside clips and the other half outside clips - 2-1153
IF, the entire joint uses outside clips - 5-178x or 5-1350x
ON the strange chance moser did what they sometimes do then you have and need a 5-212x
.Last edited by Supershafts; 01-16-2014 at 07:08 AM.
Thread Information
Users Browsing this Thread
There are currently 1 users browsing this thread. (0 members and 1 guests)
Similar Threads
-
So tell me about my u-joint
By goof4080 in forum DrivetrainReplies: 3Last Post: 07-03-2012, 03:44 PM -
Question: u joint??
By Karczewski in forum General HelpReplies: 4Last Post: 10-26-2011, 09:22 AM -
Question: Bad u-joint???
By joedude02 in forum General HelpReplies: 2Last Post: 11-02-2008, 09:09 PM -
U-Joint
By 01CalgarySS in forum DrivetrainReplies: 3Last Post: 09-18-2008, 05:43 PM -
U-joint squeaking?
By B200 in forum DrivetrainReplies: 0Last Post: 08-10-2007, 06:58 PM
Bookmarks