Results 1 to 10 of 10

Putting in a Moser

This is a discussion on Putting in a Moser within the Drivetrain forums, part of the LSx Technical Help Section category; Just ordered my Moser 9" today and should be installing it next week. Looking to see if anyone has some ...

  1. #1
    Senior Member Bottesini's Avatar
    Join Date
    Sep 2007
    Location
    Denton, Texas soon Lafayette, Louisiana
    Posts
    2,955

    Blue
    2002 Z28 Camaro M6

    Putting in a Moser

    Just ordered my Moser 9" today and should be installing it next week. Looking to see if anyone has some tips to help make things go smoother.

  2. #2
    Visualize°Design°Create SSwt00SS's Avatar
    Join Date
    Dec 2005
    Location
    Dallas, TX
    Posts
    9,287

    '12 Silver SS 1SS
    '00 Black SS #8617

    shit man, give us the goods...how did you custom order it...?

  3. #3
    Senior Member Bottesini's Avatar
    Join Date
    Sep 2007
    Location
    Denton, Texas soon Lafayette, Louisiana
    Posts
    2,955

    Blue
    2002 Z28 Camaro M6

    Quote Originally Posted by SSwt00SS View Post
    shit man, give us the goods...how did you custom order it...?
    Nothing to special

    Moser 9"
    4.11
    31 Spline
    Truetrack locker
    3 Channel ABS
    weld on LCA brackers
    and powered coated red

    with luck EPP should have it at the place in a week.

  4. #4
    Visualize°Design°Create SSwt00SS's Avatar
    Join Date
    Dec 2005
    Location
    Dallas, TX
    Posts
    9,287

    '12 Silver SS 1SS
    '00 Black SS #8617

    Quote Originally Posted by Bottesini View Post
    Nothing to special

    Moser 9"
    4.11
    31 Spline
    Truetrack locker
    3 Channel ABS
    weld on LCA brackers
    and powered coated red

    with luck EPP should have it at the place in a week.
    you're gonna like that for sure!!!

    when time comes for mine, im going Moser M9 w/3.90's and what you have listed except in black...

    get some pics of that bad boy when it comes time to install it!!!

  5. #5
    Senior Member Bottesini's Avatar
    Join Date
    Sep 2007
    Location
    Denton, Texas soon Lafayette, Louisiana
    Posts
    2,955

    Blue
    2002 Z28 Camaro M6

    Quote Originally Posted by SSwt00SS View Post
    you're gonna like that for sure!!!

    when time comes for mine, im going Moser M9 w/3.90's and what you have listed except in black...

    get some pics of that bad boy when it comes time to install it!!!
    Putting in a Racetronics fuel pump kit in at the same time, I will try to get a few good pics of things if I can. Once this is in I can finally start looking at parts to buy for the new engine

  6. #6
    Awaiting Activation
    Join Date
    Aug 2007
    Location
    odessa,texas
    Posts
    1,056

    69 hugger orange
    98 z28

    make sure you put the correct brake bracket on the correct side

    one axle is longer than the other on a 9"
    i believe it is the paSSENGER that is longer but you might check to be sure


    i found out the hard way and it cost me new bearings

  7. #7
    Member wenn_du_weinst's Avatar
    Join Date
    Aug 2008
    Location
    South Dakota
    Posts
    198
    how much was it if you don't mind me asking

  8. #8
    Awaiting Activation
    Join Date
    Aug 2007
    Location
    odessa,texas
    Posts
    1,056

    69 hugger orange
    98 z28

    my complete rear was 2100 but the bearings were like 80 plus 70 for a shop to pull the ones that i had already seated on the axles with the wrong backing plates on because i didnt notice the difference in length

  9. #9
    Senior Member Bottesini's Avatar
    Join Date
    Sep 2007
    Location
    Denton, Texas soon Lafayette, Louisiana
    Posts
    2,955

    Blue
    2002 Z28 Camaro M6

    Quote Originally Posted by wenn_du_weinst View Post
    how much was it if you don't mind me asking
    Almost 2800, would have been alot cheaper if I had not gotten it powercoated, but I won't have the time to paint it. Not to mention I got almost every other option available.

  10. #10
    Member wenn_du_weinst's Avatar
    Join Date
    Aug 2008
    Location
    South Dakota
    Posts
    198
    thats right around what I was thinking

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. Question: Putting a cam in my car need to know
    By breathnitrous in forum Computer & Tuning
    Replies: 10
    Last Post: 04-24-2010, 07:09 PM
  2. Putting them to bed.
    By pajeff02 in forum General Help
    Replies: 19
    Last Post: 11-19-2009, 08:38 PM
  3. Putting together my 408
    By lancesT/A in forum General Help
    Replies: 17
    Last Post: 08-07-2009, 12:26 PM
  4. Help: ??? putting Z06 rims on new gto's
    By beanerstib in forum Wheels and Tires
    Replies: 4
    Last Post: 03-27-2009, 07:14 PM
  5. putting the car away
    By 98redbird in forum General Help
    Replies: 6
    Last Post: 11-18-2005, 04:31 PM

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •