Results 1 to 5 of 5

Best way to remove transmission

This is a discussion on Best way to remove transmission within the Drivetrain forums, part of the LSx Technical Help Section category; Hello, What is the best way to get at the top bellhousing bolt on an A4 trany? Should I just ...

  1. #1
    Senior Member JaycenK's Avatar
    Join Date
    Nov 2008
    Location
    Holiday,FL
    Age
    40
    Posts
    1,378

    Green
    1997 Camaro Z-28

    Best way to remove transmission

    Hello, What is the best way to get at the top bellhousing bolt on an A4 trany?
    Should I just drop the back of the trans down?

  2. #2
    Royal pain in the.... Phantom2kz's Avatar
    Join Date
    Aug 2007
    Location
    savannah, ga
    Posts
    159

    2001 Z-28 A4 NBM
    2002 35th anni SS M6#1696

    support the trans, remove the crossmember/torque arm
    let trans hang off engine to access top trans bolt/harness bracket..ect...ect..
    watch that you dont break the oil pressure sender good time to change oil pressure sender,rear main and back spark plugs with trans out.

  3. #3
    Awaiting Activation
    Join Date
    Aug 2007
    Location
    odessa,texas
    Posts
    1,056

    69 hugger orange
    98 z28

    it might be necessary to jack up on the front of the motor a little also




    make sure you undo the torque converter from the flywheel,i know its common sense but i have seen people pissed because they couldnt get the tranny out and they hadnt even unbolted the t.c. yet

  4. #4
    Senior Member JaycenK's Avatar
    Join Date
    Nov 2008
    Location
    Holiday,FL
    Age
    40
    Posts
    1,378

    Green
    1997 Camaro Z-28

    LOL Actually that help because this is my first automatic I will be taking out. Everything else has been manuals.

  5. #5
    cutting and welding mark21742's Avatar
    Join Date
    Mar 2008
    Location
    mercersburg pa
    Posts
    6,443

    hugger orange
    2004

    Quote Originally Posted by JaycenK View Post
    LOL Actually that help because this is my first automatic I will be taking out. Everything else has been manuals.
    there is a small round (plug) about 11/2-2 inches across on the bottom of the bellhousing just to the driverside. pop that plug out and you can get a large flathead screwdriver in there to turn the motor over with the teeth on the flywheel. take the starter out and turn the motor till you can see the torque converter bolt in the hole where the starter was....there are 3 converter bolts..
    good luck man, dropped mine and had it back in start to finish in about 2.5 hours last weekend so its not that bad

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. How do I remove this?
    By TransAm11973 in forum General Help
    Replies: 10
    Last Post: 12-12-2008, 11:01 AM
  2. How do I remove pcm?
    By ls1monarch in forum Computer & Tuning
    Replies: 5
    Last Post: 04-21-2008, 09:00 AM
  3. clearance required to remove transmission
    By Berger21 in forum Manual Transmission
    Replies: 7
    Last Post: 03-29-2007, 09:13 AM
  4. Remove old wax.
    By timmyvws6 in forum Showcar and Detailing
    Replies: 27
    Last Post: 02-11-2006, 07:08 PM

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •