Results 1 to 6 of 6

Key Fob programing

This is a discussion on Key Fob programing within the GM Trucks forums, part of the Vehicle Specific category; Anyone know how to program a key fob to an 01 Seirra? I tried the same method as my TA ...

  1. #1
    Army Dude robcas47's Avatar
    Join Date
    Nov 2007
    Location
    Ft. Rucker Area, Lower AL
    Posts
    674

    Arctic White
    01 TA / 06 Duc 749D

    Key Fob programing

    Anyone know how to program a key fob to an 01 Seirra? I tried the same method as my TA requires but no luck.

  2. #2
    Just me Y2KPewterSS's Avatar
    Join Date
    Nov 2006
    Location
    Broken Arrow, OK
    Age
    42
    Posts
    23,353

    Pewter metallic
    2000 Camaro SS

    I searched around the net and found this, might try it:

    1. Get in truck and close all doors
    2. Put key in ignition
    3. Press and hold the door unlock switch
    4. While holding door unlock swich, cycle ignition 2 times, ON-OFF-ON-OFF
    5. Release the door unlock switch, the door locks should lock and unlock to confirm the programming mode
    6. Press and hold the LOCK and UNLOCK buttons simultaneously on one transmitter. After a delay of approximately 15 seconds the doors will lock and unlock to confirm the programming of that transmitter
    7. Repeat step 6 for each additional transmitter (up to 4), including any you had before.
    8. Turn key to RUN to exit programming mode.
    9. Operate the transmitter functions to ensure correct system operation.

  3. #3
    She Moderator KahanaReef's Avatar
    Join Date
    Jul 2008
    Location
    So Cal
    Age
    54
    Posts
    15,591

    Arctic White
    2000 Camaro Z28

    I found the same on gm-trucks.com

  4. #4
    Just me Y2KPewterSS's Avatar
    Join Date
    Nov 2006
    Location
    Broken Arrow, OK
    Age
    42
    Posts
    23,353

    Pewter metallic
    2000 Camaro SS

    Quote Originally Posted by KahanaReef View Post
    I found the same on gm-trucks.com
    That was where I found it

  5. #5
    Bone it like you own it FORD RECOVERY EXPERT's Avatar
    Join Date
    Sep 2005
    Location
    TEXAS... U mad?
    Posts
    6,158

    Black / Stryker Blue
    2K WS.6/ 2K9 G8GT

    Quote Originally Posted by GM Tech Manual View Post
    Transmitter Programming

    Important
    All transmitters which are to be recognized by the remote control door lock receiver (RCDLR) must be programmed in a single programming sequence. If the system is placed in program mode it will erase all previously programmed transmitters upon the receipt of the programming signal from the first transmitter. Up to four transmitters can be programmed. Do not operate or program the transmitters in the vicinity of other vehicles that are in the keyless entry program mode. This prevents the programming of the transmitters to the incorrect vehicle.


    You may program up to 4 transmitters, using either of the two following procedures:

    Transmitter Programming Procedure (Method 1 - No Tools Required)
    Close all the vehicle doors.
    Insert the ignition key into the ignition lock cylinder.
    Press and hold the door unlock switch.
    While holding the door lock switch in the unlock position, cycle the ignition ON, OFF, ON, OFF.
    Release the door unlock switch. The doors will lock and unlock to confirm the program mode.
    Press and hold the LOCK button and the UNLOCK button simultaneously on one transmitter. After a delay of approximately 15 seconds, the doors will lock and unlock to confirm the programming of that transmitter.
    Repeat the previous step to program up to four transmitters.
    Turn the ignition switch to the RUN position in order to exit the keyless entry transmitter mode.
    Operate the transmitter functions in order to verify correct system operation

    You MUST program all remotes at the same time. Programming one new remote will change the code causing any existing remotes to no longer work.

    Try this.....

  6. #6
    Army Dude robcas47's Avatar
    Join Date
    Nov 2007
    Location
    Ft. Rucker Area, Lower AL
    Posts
    674

    Arctic White
    01 TA / 06 Duc 749D

    Will try here in a minute. thanks Y2KPewter

    This worked, thanks again.
    Last edited by robcas47; 06-28-2011 at 12:05 PM. Reason: follow up

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. O2 Sensors Programing
    By toenale56 in forum Computer & Tuning
    Replies: 4
    Last Post: 05-06-2010, 11:28 AM
  2. Direct Tv programing ?
    By redls1 in forum Almost Anything Goes
    Replies: 0
    Last Post: 04-06-2010, 01:42 PM
  3. Programing our Vehicle's
    By FORMULA7 in forum Computer & Tuning
    Replies: 1
    Last Post: 09-15-2006, 08:01 PM
  4. Programing LS6
    By Footloose in forum Computer & Tuning
    Replies: 4
    Last Post: 06-15-2006, 02:44 PM
  5. Programing Keyless Entry
    By GOAT6SPD in forum Western Members
    Replies: 10
    Last Post: 09-07-2005, 03:48 PM

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •