Results 1 to 7 of 7

New clutch why wont tranny slide in?????

This is a discussion on New clutch why wont tranny slide in????? within the Manual Transmission forums, part of the Drivetrain category; I just installed my stage 4 spec and im trying to slide the tranny back in and it gets to ...

  1. #1
    Member RS_SS69's Avatar
    Join Date
    Jan 2006
    Location
    Denver
    Posts
    593

    Onyx Black
    2001 SS

    New clutch why wont tranny slide in?????

    I just installed my stage 4 spec and im trying to slide the tranny back in and it gets to about 1 inch away and wont go any further, what the hell am i missing or doing wrong here, I need the car it is my daily driver please someone help!

  2. #2
    Junior Member
    Join Date
    Aug 2006
    Location
    IN
    Age
    40
    Posts
    7

    Black
    '02 WS/6

    Did you get everything worked out?

  3. #3
    Member lrader99's Avatar
    Join Date
    Nov 2005
    Location
    NW Georgia
    Age
    32
    Posts
    397

    flat black
    Pilot Bearing

  4. #4
    Junior Member preppy's Avatar
    Join Date
    Aug 2006
    Location
    ga
    Posts
    19

    silver
    2000 ws6 transam

    your disc is off center. take tranny back out , loosen the clutch andstick fingers behind it to make sure its even all the way around, try again When its right it will go - dont force it

  5. #5
    Junior Member extanker's Avatar
    Join Date
    Jun 2006
    Location
    trenton nj
    Age
    64
    Posts
    62

    black
    07 z06

    before you installed it did you take the disc and slide it on the input shaft or is this the first clutch job you have done

  6. #6
    Senior Member ninobrn99's Avatar
    Join Date
    Aug 2003
    Location
    Honolulu HI
    Age
    34
    Posts
    2,486

    Pewter
    all bore 370 Trans Am

    it needs finessing. it wasnt installed wrong. you need to force it in. get it as close as possible and then use the bolts to pull it in the rest of the way.

  7. #7
    Insane WinSomeLoseNone's Avatar
    Join Date
    Dec 2005
    Location
    PA - Montgomery County
    Posts
    185

    Black
    2000 Camaro Z28 M6

    I just installed my trans yesterday and had this problem. The slave cylinder contacts the clutch fingers and had enough strength to prevent you from inserting trans. Go to a hardware store and buy the same size and thread as your trand to bellhousing bolts only longer and use them (possibly some sort of spacer on the bolt) to pull the trand together. then somply swap the screws with the regular screws one at a time. Then again my clutch is fucked up and i cant drive cause something is wrong...

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. Help: Tranny wont go into Gear!!!
    By El Toro Loco in forum Manual Transmission
    Replies: 8
    Last Post: 04-18-2013, 09:01 AM
  2. Tranny Wont kick down
    By redbird555 in forum Automatic Transmission
    Replies: 2
    Last Post: 04-17-2010, 11:31 AM
  3. Tranny wont engage! AHHHHH!!!!!
    By sicknick530 in forum Drivetrain
    Replies: 2
    Last Post: 03-07-2008, 05:38 PM
  4. tranny wont shift on its own!!!
    By Ls1fury in forum Automatic Transmission
    Replies: 10
    Last Post: 10-01-2007, 02:30 PM
  5. installing clutch and tranny wont slide in???
    By RS_SS69 in forum Rocky Mountain Members
    Replies: 6
    Last Post: 07-25-2006, 06:53 PM

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •