Results 1 to 5 of 5

need help with hydraulic line

This is a discussion on need help with hydraulic line within the Manual Transmission forums, part of the Drivetrain category; Im trying to disconnect the hydraulic line that connects to the slave cylinder but it wont come off.. I know ...

  1. #1
    Member turyg ls1's Avatar
    Join Date
    Apr 2010
    Location
    Clewiston,Fl
    Posts
    107

    Pewter
    2002 camaro ss slp #2582

    need help with hydraulic line

    Im trying to disconnect the hydraulic line that connects to the slave cylinder
    but it wont come off.. I know u have to push in the plastic ring , it also has a metal clip that clips on side ways.. my ? is does that clip have to come off completly and if so theres not enough room to remove it all the way...
    can anybody help me solve this problem

  2. #2
    expensive tires az gt eater's Avatar
    Join Date
    Mar 2006
    Location
    phoenix
    Posts
    1,951

    white
    04 2500 4x4 crew cab

    you can use two flat bladed screw drivers to push that plastic ring in. That will be what it takes to get it off. Pull on the hose at the same time. Be careful you don't break the plastic ring. I bought the fuel line disconnect tools to use the second time around. It was still hard, but it was a little easier with the tool. I can't remember the size. I bought three of them. The plastic set of these tools didn't do the trick. I bought the aluminum ones from checkers.

  3. #3
    Member turyg ls1's Avatar
    Join Date
    Apr 2010
    Location
    Clewiston,Fl
    Posts
    107

    Pewter
    2002 camaro ss slp #2582

    Well I just changed the slave myself and I still have the tool that came with it but like said there's a metal clip right behind the plastic ring its on the slave part.. U know what I'm talkin about ?

  4. #4
    Moderator Cutlass's Avatar
    Join Date
    Apr 2008
    Location
    Madison, WI
    Posts
    6,996

    1999 Formula WS6 M6-sold
    2001 Silverado Z71

    The white plasic collar needs to be pushed inside the slave fitting. It somewhat easy to push the while collar flush with the slave fitting, but a little trickier pushing it inside a little bit.
    I don't remember a metal clip being in the way...but its been a while.

  5. #5
    Member
    Join Date
    Sep 2010
    Location
    WI
    Posts
    129
    2000 Trans Am

    Quote Originally Posted by Cutlass View Post
    The white plasic collar needs to be pushed inside the slave fitting. It somewhat easy to push the while collar flush with the slave fitting, but a little trickier pushing it inside a little bit.
    I don't remember a metal clip being in the way...but its been a while.
    Yea, you should only have the plastic white collar that needs to be pressed in on the quick connect but thats all there is to it. Easier said then done of course.

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. Hydraulic Clutch Line Remover Tool
    By SuperSport346 in forum Tools
    Replies: 6
    Last Post: 02-11-2010, 05:41 PM
  2. how do i get clutch hydraulic line back in??
    By jmatt07 in forum General Help
    Replies: 8
    Last Post: 10-21-2009, 06:49 AM
  3. Wanted: Hydraulic master cylinder clutch line
    By Chronic442 in forum Parts Wanted / Trade
    Replies: 0
    Last Post: 05-12-2008, 03:56 PM
  4. NTB: Hydraulic Clutch Line 98-02 TA
    By rbrack in forum Parts Wanted / Trade
    Replies: 2
    Last Post: 12-11-2007, 07:28 PM
  5. Braided Hydraulic line
    By FunkyTownFBody in forum Manual Transmission
    Replies: 0
    Last Post: 11-14-2005, 07:36 PM

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •