Results 1 to 20 of 25
Thread: what size cutout
-
11-24-2007, 11:12 AM #1
what size cutout
which size would I need for my 99 trans am
https://shop.quicktimeperformance.co...oduct_list&c=9
Thanks
-
11-24-2007, 11:15 AM #2
3" and dont look back
-
11-24-2007, 11:18 AM #3
alrighty, thanks.
-
11-24-2007, 11:19 AM #4
damn lookin at your pic... I need 2 wash my car and then take a new pic.... My pic is not good looking.
Last edited by Justin23454; 11-24-2007 at 02:25 PM.
-
11-24-2007, 11:28 AM #5
thanks man. That was taken last september after a full day of detailing it. I have a 3" in my car and it is LOUD when uncapped. The whole car shakes and rumbles. I only open it up at the track/shows/cruises etc... My exhaust is loud enough.
-
11-24-2007, 11:32 AM #6
do you notice a diff in power or just sound?
-
11-24-2007, 11:33 AM #7
-
11-24-2007, 05:56 PM #8
I got the 3" electric cut out and I agree it sounds good (but beware of where you open it at...lol)
-
11-25-2007, 08:35 AM #9
im 2 poor 2 get the electric.
-
11-25-2007, 08:43 AM #10
yeah they are a little expensive
-
11-25-2007, 08:44 AM #11
same here but when I get the $$$ I am going to add on the electric.
Manual will do just fine till then. The guy that welded mine on, welded the bolts on and put some wing nuts on it. Easy and fast to cap/uncap it. Have it put in the I pipe right b4 the exaust goes over the axle (on the right side of your car in front of your rear wheel)
-
11-25-2007, 08:54 AM #12
sounds good, guess Ill order one today.
-
11-25-2007, 09:27 AM #13
-
11-25-2007, 09:45 AM #14
im stock exhaust
-
11-25-2007, 10:10 AM #15
I got mine running through longtubes & y pipe (no cats) and stock catback. You gotta get one.. well worth it!
-
11-25-2007, 10:39 AM #16
-
11-25-2007, 10:51 AM #17
-
11-25-2007, 11:41 AM #18
45-70$ isnt to much, but 350-400 is alittle more then I have right now.
-
11-25-2007, 11:42 AM #19
-
11-25-2007, 12:12 PM #20
ok will do
Thread Information
Users Browsing this Thread
There are currently 1 users browsing this thread. (0 members and 1 guests)
Similar Threads
-
What Size Cutout for Firehawk?
By 98BlackTransAm in forum External EngineReplies: 1Last Post: 09-26-2010, 09:33 AM -
LS1 valley cover bolt size, what size?
By Blue28 in forum External EngineReplies: 1Last Post: 10-03-2009, 05:47 PM -
Cutout Size
By ss~zoso~ss in forum External EngineReplies: 23Last Post: 02-13-2007, 03:30 PM -
What size cutout with this setup?
By WinSomeLoseNone in forum External EngineReplies: 8Last Post: 01-27-2006, 07:35 PM -
What size cutout do I need?
By ram air ws6 in forum External EngineReplies: 1Last Post: 09-21-2005, 08:12 PM
Bookmarks