Results 1 to 5 of 5

Need some help after Intake/Cam install

This is a discussion on Need some help after Intake/Cam install within the External Engine forums, part of the LSx Technical Help Section category; I have 2 connections I can't figure where they go. There is a wire/sensor plug located on the drivers side, ...

  1. #1
    Junior Member
    Join Date
    Aug 2005
    Location
    Texas
    Age
    53
    Posts
    5

    Pewter
    2000 Z28

    Need some help after Intake/Cam install

    I have 2 connections I can't figure where they go. There is a wire/sensor plug located on the drivers side, by the #7 fuel injector plug that I can't figure out where it goes. Also, I installed the new Professional Products intake and on the front of it, on the passengers side, need where the throttle body is bolted, is a outlet that I can't figure out where it is suppose to attach.

    Any help would be greatly appreciated. The car will start and run, but when you give it more than slight throttle, it bogs down and doesn't want to speed up.

  2. #2
    Junior Member
    Join Date
    Aug 2005
    Location
    Wahiawa hi.
    Age
    41
    Posts
    10

    black
    2000 Camaro SS

    post up a pic of the wires, its hard to tell from the discription, but with a pic id be able to tell you quick

  3. #3
    Junior Member
    Join Date
    Aug 2005
    Location
    Texas
    Age
    53
    Posts
    5

    Pewter
    2000 Z28

    Here you go the first one I had plugged as I think it went to the AIR system, which I removed.
    The second image, I had the red plug and white plug attached to the connectors next to them.

    The third image is of the connector I can't figure out.

  4. #4
    Junior Member
    Join Date
    Aug 2005
    Location
    Wahiawa hi.
    Age
    41
    Posts
    10

    black
    2000 Camaro SS

    the second pic looks like you had the plugs in the right place.. remember, all of your connectors will only connect in one place..

    the third pic, not sure, but make sure you have these two connectors hooked up, kinda looks like the oil pressure sending unit connector, but not 100%

  5. #5
    Junior Member
    Join Date
    Aug 2005
    Location
    Texas
    Age
    53
    Posts
    5

    Pewter
    2000 Z28

    I found the tubing for the PCV that runs from the Intake to both valve covers, so that mistery is solved, now I just need to find out where the connector in the 3rd picture goes. I guess I will have to tear the intake off and see if I can find it that way. It still runs with a hesitation, kind of like it has a vacuum leak.

    Thanks for all your help.

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. Question: F.A.S.T Intake Install
    By Dr.Crash in forum External Engine
    Replies: 17
    Last Post: 02-05-2009, 04:28 PM
  2. Intake install
    By Wheeler99WS6 in forum External Engine
    Replies: 0
    Last Post: 04-09-2007, 05:38 PM
  3. what to a intake install
    By momsls1 in forum External Engine
    Replies: 4
    Last Post: 09-21-2006, 12:46 AM
  4. ls1 intake install
    By wayfastws6 in forum External Engine
    Replies: 1
    Last Post: 04-16-2006, 11:51 AM
  5. ls6 intake ? INSTALL KIT
    By skar in forum General Help
    Replies: 3
    Last Post: 02-27-2006, 03:37 AM

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •