Results 1 to 8 of 8

E-Cutout Sweetness

This is a discussion on E-Cutout Sweetness within the External Engine forums, part of the LSx Technical Help Section category; Hi all, Just showing off my new DMH E-Cutout. I had it welded in the I pipe under the rear ...

  1. #1
    Member BlackSS1's Avatar
    Join Date
    Jun 2007
    Location
    Lexington, NC
    Posts
    460

    Black
    2001 Camaro SS Vert

    E-Cutout Sweetness

    Hi all,
    Just showing off my new DMH E-Cutout.

    I had it welded in the I pipe under the rear passenger seat, and I wired it to a switch on my console. It is the round switch next to the convertible top switch.

    Also added a turndown tip to point the noise and fumes out to the side of the car. Turned out nicely, cannot be seen from the side, and sounds freakin AWESOME!

    This runs to a Magnaflow catback so it is quiet when need be also.



    Last edited by BlackSS1; 02-28-2010 at 12:59 PM. Reason: corrected an inaccuracy in the post

  2. #2
    Veteran Hi-Po's Avatar
    Join Date
    Nov 2005
    Location
    Florida
    Posts
    10,461

    Black
    1999 TA WS.6

    Looks really nice, like the switch placement. Love my DMH.

  3. #3
    Electrical Engineer KMdef9's Avatar
    Join Date
    Jul 2009
    Location
    North of the Motorcity
    Posts
    2,611

    Custom Swirly Black
    2001 WS6 M6

    Nice setup! How much did it run you? Is your car tuned for the cutout?

  4. #4
    Member marksls1ta's Avatar
    Join Date
    Dec 2006
    Location
    pikeville, kentucky
    Posts
    701

    black
    1998 trans am

    looks nice...

  5. #5
    Member BlackSS1's Avatar
    Join Date
    Jun 2007
    Location
    Lexington, NC
    Posts
    460

    Black
    2001 Camaro SS Vert

    Quote Originally Posted by KMdef9 View Post
    Nice setup! How much did it run you? Is your car tuned for the cutout?
    Thanks, it ran about $275 for all parts and including $40 for the welding. Tune is not changed for the cutout... just did it for the sound effects really.

    Every mustang in town tries to race me now that they can hear the cam.

  6. #6
    Super Moderator
    pajeff02's Avatar
    Join Date
    Feb 2009
    Location
    Mansfield, PA
    Posts
    21,576

    Black & Blue
    '02 WS.6 / '07 Suburban

    Nice! Where did you find a turn down with a flange? I have the same cutout to install on our car and also want to go with a turndown to keep the underside of the car from getting all black.

  7. #7
    Member BlackSS1's Avatar
    Join Date
    Jun 2007
    Location
    Lexington, NC
    Posts
    460

    Black
    2001 Camaro SS Vert

    Quote Originally Posted by pajeff02 View Post
    Nice! Where did you find a turn down with a flange? I have the same cutout to install on our car and also want to go with a turndown to keep the underside of the car from getting all black.
    Thanks. I found it at Jegs. I actually have an extra since they only sell them in pairs if you're interested... It comes with bolts, but I had to buy longer bolts to extend through all the parts.

  8. #8
    Super Moderator
    pajeff02's Avatar
    Join Date
    Feb 2009
    Location
    Mansfield, PA
    Posts
    21,576

    Black & Blue
    '02 WS.6 / '07 Suburban

    Quote Originally Posted by BlackSS1 View Post
    Thanks. I found it at Jegs. I actually have an extra since they only sell them in pairs if you're interested... It comes with bolts, but I had to buy longer bolts to extend through all the parts.

    Will send a PM.

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. Cutout
    By 1998ss in forum External Engine
    Replies: 22
    Last Post: 11-19-2010, 08:25 AM
  2. SLP lid and NEW cutout
    By oneBADDz in forum Parts For Sale / Trade
    Replies: 5
    Last Post: 11-25-2007, 04:42 PM
  3. cutout!
    By Raoul-Duke in forum External Engine
    Replies: 11
    Last Post: 11-20-2006, 03:37 PM
  4. cutout
    By JattGunMan in forum External Engine
    Replies: 6
    Last Post: 04-26-2006, 03:27 PM
  5. Need help with cutout
    By JattGunMan in forum External Engine
    Replies: 2
    Last Post: 03-24-2006, 11:29 AM

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •