Results 1 to 20 of 24
Thread: Cutout Size
-
01-30-2007, 04:24 AM #1
Cutout Size
First of all, what diameter is the intermediate pipe on a 98 SS,
Second, for all of you that do have cutouts where did u have them installed on the system, and where did u get a turndown
Three, how much louder , how much performance do u gain ( not necessarily numbers but can u feel it?)
Jeff98' SS Convertible Camaro-76k-Build # 1471, Cragar SS rims, RK SFC's, MAC Panhard, LSX Tune, Shaner S3,
SLP:short thro,Strut tower brace,fan switch
MTI Power induction kit,40 Series muffler,Pacesetter LT's + ORY,12 CD changer,3800lbs
http://www.cardomain.com/ride/787506/1
-
01-30-2007, 02:36 PM #2
I think the intermediate pipe is not quite 3" Just a tad smaller.
-
01-30-2007, 05:06 PM #3
intermediate pipe is 2.75". get a 3" cutout. here's my webpage back when i had one. results on that page.
http://www.stealthram.com/qtpcutout.htmlCold Air Intake, Muffler Delete, Vinci High Performance Dual Valve Springs, Hardened Pushrods, Yella Terra 1.85 Rockers, Some Hydropdipped Stuff, Strut Tower Brace, Some SS Badges, boost/vacuum gauge, fuel pressure gauge, some checkered stripes, drilled/slotted rotors, ZL1addons Stealth wickerbill, Ruxifey LED side markers
-
01-31-2007, 05:21 AM #4
thanks a bunch man, this and plugs+wires will be the only mods i can afford
-
01-31-2007, 06:56 PM #5
I put mine a little after the passenger side CAT.
-
02-03-2007, 09:15 PM #6
Mine is under the rear seat. I think you'll be happy with the cutout. Are you still running cats? Back when I had cats I ran mine open 24/7.
-
02-05-2007, 01:17 PM #7
yea i still have cats, i want to get a 3 inch Y with high flows but i dont have the money yet
-
02-05-2007, 01:17 PM #8
does anybody know where i can buy a turndown that bolts onto the cutout
-
02-05-2007, 01:21 PM #9
-
02-05-2007, 01:34 PM #10
i have looked there, couldnt find it
-
02-05-2007, 01:36 PM #11
alright i found it but they're too long, i've seen people that have short ones i need one of those
-
02-05-2007, 01:37 PM #12
I could make you a set?
-
02-05-2007, 03:31 PM #13
yeah i through in a cut out for sound only.. if u ever decide to run an ory without cats, you won't want the cutout open, you need back pressure for power. since you still have a stock exhaust though, you should feel an increase of about 6-7 i think. and it'll sound niiice
-
02-05-2007, 06:20 PM #14
yea i'm hopin for that, i know the power aint much but i hope it sounds good
-
02-05-2007, 06:25 PM #15
its a decent increase and hey, every little bit counts, and the cut out will definitly sound good good luck man
-
02-05-2007, 06:28 PM #16
yo, uconn just rejected my app.. lol
-
02-05-2007, 06:28 PM #17
Why don't you just go with the Flowtech turndowns with 3 bolt flanges allready welded on and cut it to length?
-
02-06-2007, 10:37 AM #18
-
02-06-2007, 10:37 AM #19
-
02-06-2007, 03:43 PM #20
im finishing with a 3.7 gpa.. they probably didnt want me cause i was in the low 50% on sats and im outa state.. o well, good school though lol
Thread Information
Users Browsing this Thread
There are currently 1 users browsing this thread. (0 members and 1 guests)
Similar Threads
-
What Size Cutout for Firehawk?
By 98BlackTransAm in forum External EngineReplies: 1Last Post: 09-26-2010, 09:33 AM -
LS1 valley cover bolt size, what size?
By Blue28 in forum External EngineReplies: 1Last Post: 10-03-2009, 05:47 PM -
what size cutout
By Justin23454 in forum External EngineReplies: 24Last Post: 11-29-2007, 06:38 PM -
What size cutout with this setup?
By WinSomeLoseNone in forum External EngineReplies: 8Last Post: 01-27-2006, 07:35 PM -
What size cutout do I need?
By ram air ws6 in forum External EngineReplies: 1Last Post: 09-21-2005, 08:12 PM
Bookmarks