Results 1 to 7 of 7
Like Tree1Likes
  • 1 Post By pajeff02

valve cover

This is a discussion on valve cover within the General Help forums, part of the LSx Technical Help Section category; does anyone has a passage side valve cover off a ls1 engine ,what I need is a picture of the ...

  1. #1
    Member
    Join Date
    Feb 2008
    Location
    jupiter fl.
    Posts
    152

    white
    2000 trans am

    valve cover

    does anyone has a passage side valve cover off a ls1 engine ,what I need is a picture of the under side so I can see the locking tab that holds the factory fill tube on the cover so I can possibly bend it out of the way to remove the tube whi tout taking the cover off. thanks

  2. #2
    Super Moderator
    pajeff02's Avatar
    Join Date
    Feb 2009
    Location
    Mansfield, PA
    Posts
    21,576

    Black & Blue
    '02 WS.6 / '07 Suburban

    I only took pics of the top of the covers when I polished them a few years back.

  3. #3
    Super Moderator
    pajeff02's Avatar
    Join Date
    Feb 2009
    Location
    Mansfield, PA
    Posts
    21,576

    Black & Blue
    '02 WS.6 / '07 Suburban

    Just for fun, I Googled "ls1 oil fill tube" and came up with a couple of good pics under "Images".

  4. #4
    Member
    Join Date
    Feb 2008
    Location
    jupiter fl.
    Posts
    152

    white
    2000 trans am

    thankyou pajeff that's just what I needed to see

  5. #5
    Super Moderator
    pajeff02's Avatar
    Join Date
    Feb 2009
    Location
    Mansfield, PA
    Posts
    21,576

    Black & Blue
    '02 WS.6 / '07 Suburban

    I was afraid to break it and just worked around mine. Even though you really can't see them, a polished stock cover looks pretty good.



    SMWS6TA likes this.

  6. #6
    Spaz is My Mentor SMWS6TA's Avatar
    Join Date
    Feb 2009
    Location
    Ugy Lower Corner of AL
    Posts
    10,511

    Navy Blue Metallic
    98 T/A w/a little mods...

    How'd you do it?

  7. #7
    Super Moderator
    pajeff02's Avatar
    Join Date
    Feb 2009
    Location
    Mansfield, PA
    Posts
    21,576

    Black & Blue
    '02 WS.6 / '07 Suburban

    Hand sanded the rougher areas with 400 wet, ran a soft Dryloc over the entire thing with my angle die grinder, and then polished them with a buffing wheel in my straight die grinder. Did not take long at all.

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. coil cover idea... sbc valve cover
    By BLK2KSS in forum Appearance Section
    Replies: 24
    Last Post: 11-14-2012, 08:19 AM
  2. Question: Valve Cover 97/98 Z28
    By Paulie in forum General Help
    Replies: 16
    Last Post: 10-25-2010, 11:03 AM
  3. Help: valve cover too low
    By timowen1 in forum General Help
    Replies: 17
    Last Post: 10-15-2010, 09:54 AM
  4. Valve cover gaskets, Valve Springs, Timing Gasket
    By Dewman in forum Parts For Sale / Trade
    Replies: 0
    Last Post: 01-22-2010, 09:14 PM
  5. Valve Cover Breather/ PCV Valve
    By lonewolf37 in forum General Help
    Replies: 0
    Last Post: 10-26-2007, 03:24 AM

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •