New to LT Headers

**My00Z28** · 03-16-2011, 11:39 AM

So i picked up my Bosch 13111 O2 sensors today and OMG this bad boys are LONG i haven't compared them to the headers yet but i compared them to a factory O2 in Advance and DAMN lol.... is there any routing things people do when tucking the cables away? lol

***SMWS6TA*** · 03-16-2011, 12:39 PM

Follow the wiring for the original O2 wires. I zipped tied mine to follow the rear O2 harness. Just make sure you keep them away from the headers.

**My00Z28** · 03-16-2011, 12:54 PM

alrighty just seeing what people do!!!!

***SMWS6TA*** · 03-16-2011, 01:16 PM

what headers did you get?

**My00Z28** · 03-16-2011, 01:19 PM

haha i was hoping no one would ask.... im going to try out some ebay headers.... iv looked them up a bit and there are alot of good people have said about them... hoping i will be able to say the same!!!

**jiveass** · 03-16-2011, 01:24 PM

Originally Posted by My00Z28

haha i was hoping no one would ask.... im going to try out some ebay headers.... iv looked them up a bit and there are alot of good people have said about them... hoping i will be able to say the same!!!

i got the ebay headers....nothin wrong with em im my opinion.....which ones are you lookin to get?

**My00Z28** · 03-16-2011, 01:26 PM

i ordered them already from DPTMotorsport

**jiveass** · 03-16-2011, 01:29 PM

did a search and couldnt find them....i got mine from DNAmotoring....

**My00Z28** · 03-16-2011, 01:31 PM

ya i would think they are all pretty much the same sold by different people!!

**jiveass** · 03-16-2011, 01:32 PM

i couldnt get mine in there at all...even with the engine jacked up....but once i installed polyurethane motor mounts they slid right in...i dont understand it....

**My00Z28** · 03-16-2011, 01:55 PM

im praying i wont need any cause i dont have an extra 200 bucks for motor mounts

**jiveass** · 03-16-2011, 03:21 PM

Originally Posted by My00Z28

im praying i wont need any cause i dont have an extra 200 bucks for motor mounts

$200? where you gettin that price at? i got mine from ebay for $70ish dollars....well worth it, cause once you get the headers in, you dont wanna attempt to swap the mounts later on....might as well do it now..

**My00Z28** · 03-16-2011, 03:23 PM

advance auto parts is 100 bucks each!

**jiveass** · 03-16-2011, 03:25 PM

Originally Posted by My00Z28

advance auto parts is 100 bucks each!

actually they are cheaper than i quoted...here ya go

http://cgi.ebay.com/ebaymotors/PROTH...Q5fAccessories

**Cutlass** · 03-16-2011, 07:02 PM

I ran my passenger side sensor up towards the starter, made a few loops and zip tied it up to something up in that area. I ran my drivers side sensor over to the passenger side, then down along the Kmember and over to the drivers side to plug it in. here's a pic

PaJeff did something similar.

**My00Z28** · 03-16-2011, 07:50 PM

Originally Posted by Cutlass

I ran my passenger side sensor up towards the starter, made a few loops and zip tied it up to something up in that area. I ran my drivers side sensor over to the passenger side, then down along the Kmember and over to the drivers side to plug it in. here's a pic