Results 1 to 5 of 5

Loose door window....Help!!!

This is a discussion on Loose door window....Help!!! within the General Help forums, part of the LSx Technical Help Section category; When my window is down I can slide it about 2 inches in either direction (side to side or back ...

  1. #1
    Member jeremy_m70's Avatar
    Join Date
    Dec 2006
    Location
    ALABAMA
    Age
    37
    Posts
    132

    SILVER
    1998 Z28

    Loose door window....Help!!!

    When my window is down I can slide it about 2 inches in either direction (side to side or back and forth) When rolling it up I have to manually guide it in track and when up it can tilt or fall inwards towards the inside. I have seen where some wrote that a bolt had became loose in the regulator but all I can find are rivets and no bolts. I noticed when I took off the door panel at the top of the inner panel there are two bolts holding a clamp and one also has a brass looking U shaped metal piece bolted with one of the two bolts. It appears the brass piece could be broke and what has been scratching up my tint. Any Thoughts??

  2. #2
    Member jeremy_m70's Avatar
    Join Date
    Dec 2006
    Location
    ALABAMA
    Age
    37
    Posts
    132

    SILVER
    1998 Z28

    Oh yea it is a 1998 z28 and drivers side.

  3. #3
    Life in the Fast lane sunsetorangess's Avatar
    Join Date
    Aug 2005
    Location
    Bragg NC
    Posts
    2,835

    Met. Sunset Orange
    01 SS

    I had the same issue on my 97, i had a few scratches all the way up my window in the tint, finaly i took the door off and there are two "brass looking clamps that should have felt or some type of soft material on the end. If its missing it will scratch your window to shit and also let it flop back and forth. Should only be one bolt on each of them to remove, and either order them from Gm or junk yard. i went to a junkyard and picked mine up.
    Its a simple fix once you get the parts.
    J
    2001 SS, Its not the car its the Driver that matters....

  4. #4
    Senior Member
    Join Date
    Jul 2005
    Location
    Jacksonville, FL
    Posts
    2,725
    Sounds like the stabilizers, could be something else going on too. Check out http://shbox.com/1/adj_window.html

  5. #5
    Member jeremy_m70's Avatar
    Join Date
    Dec 2006
    Location
    ALABAMA
    Age
    37
    Posts
    132

    SILVER
    1998 Z28

    Thanks Guys, as we say in Alabama, y'all made my day. I did do a forum search but the results are listed by most current and not relevant. I looked until I couldn't see straight. Thanks again!!!

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. Weird Vibrating / Loose part sound under ACCEL
    By ss~zoso~ss in forum General Help
    Replies: 9
    Last Post: 07-15-2007, 01:43 PM
  2. Loose Rear End?
    By Mike's TA in forum Drivetrain
    Replies: 1
    Last Post: 02-21-2007, 08:24 PM
  3. K&N air filter, loose piece of wire found WARNING
    By SV8 in forum External Engine
    Replies: 1
    Last Post: 03-03-2006, 04:48 PM
  4. Broke Loose, G35 Pulled.... Damn It!
    By Street Lethal in forum Kill Stories
    Replies: 38
    Last Post: 01-03-2006, 06:11 AM
  5. Loose Shifter?
    By x10-wakerider in forum Manual Transmission
    Replies: 10
    Last Post: 09-02-2005, 01:57 PM

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •