Results 1 to 9 of 9
Thread: knock sensors
-
04-22-2012, 09:23 PM #1
- Join Date
- Apr 2009
- Location
- Tyler TX
- Age
- 34
- Posts
- 516
Navy Blue Metallic/Black- 02 camaro z28/01 wife t/a
knock sensors
i got a code that pops up goes away and then pops back on again is p0332 i believe. My knock sensors Now i am running a cam and the engine does rock back and forward im guessing because of the cam could my cam be making this code pop up or is it something else? i dont really hear my engine knocking just a small ticking like the lifters. the oil pressure is normal, and my fuel pressure some times wen cold my fuel gauge located at the fuel rail reads zero, i dont know if thats normal.
thanks for the help
-
04-22-2012, 09:49 PM #2
- Join Date
- Oct 2008
- Location
- Coral Springs, Fl
- Posts
- 5,774
Sunset Orange Metalic- 2001 Camaro SS
It reads zero when off? Did you check the motor mounts, the cam might cause a little more motion but it shouldn't be rocking around violently. Also was the car tuned for the cam?
-
04-23-2012, 12:24 PM #3
- Join Date
- Apr 2009
- Location
- Tyler TX
- Age
- 34
- Posts
- 516
Navy Blue Metallic/Black- 02 camaro z28/01 wife t/a
naw is not violently and yes its been dyno tune and it only reads zero some times not all the time
-
04-23-2012, 04:14 PM #4
- Join Date
- Oct 2008
- Location
- Coral Springs, Fl
- Posts
- 5,774
Sunset Orange Metalic- 2001 Camaro SS
When you did the cam did you replace the knock sensors? The harness could also be a cause of it. If you havent changed these i suggest replacing them with new ones and a new harness.
-
04-23-2012, 04:24 PM #5
- Join Date
- Apr 2009
- Location
- Tyler TX
- Age
- 34
- Posts
- 516
Navy Blue Metallic/Black- 02 camaro z28/01 wife t/a
is that what the code means? p0332 is it bad to run the car like that? i mean it drives really good with no problem
-
04-23-2012, 04:47 PM #6
- Join Date
- Oct 2008
- Location
- Coral Springs, Fl
- Posts
- 5,774
Sunset Orange Metalic- 2001 Camaro SS
Well it's just pulling timing. A bad knock sensor can cause a car to lose lots of power, i really recommend swapping out sensors. The sensor is just for bank 2 but if the sensors have never been replaced i would swap them both out along with the harness, it's just good insurance. New ACDelco Replacements is the only way i would go though. Have had really bad luck with aftermarket brands
Here are the part numbers if you end up doing it
Knock Sensor - 12589867
Harness - 12601822
-
04-23-2012, 06:27 PM #7
- Join Date
- Apr 2009
- Location
- Tyler TX
- Age
- 34
- Posts
- 516
Navy Blue Metallic/Black- 02 camaro z28/01 wife t/a
ok thanks i kinda got a felling that if i swap them out there still going to come on. But im thinking on doing the lsxr intake and if i do it ill replace everything will im at it and take her for another dyno tune
-
04-23-2012, 06:35 PM #8
- Join Date
- Oct 2008
- Location
- Coral Springs, Fl
- Posts
- 5,774
Sunset Orange Metalic- 2001 Camaro SS
Even better
-
04-24-2012, 08:57 AM #9
- Join Date
- Apr 2009
- Location
- Tyler TX
- Age
- 34
- Posts
- 516
Navy Blue Metallic/Black- 02 camaro z28/01 wife t/a
yeah if i do that work i want some goody's as well
Thread Information
Users Browsing this Thread
There are currently 1 users browsing this thread. (0 members and 1 guests)
Similar Threads
-
Question: Knock Sensors
By Keith01 in forum General HelpReplies: 8Last Post: 07-27-2011, 10:58 AM -
Knock Sensors
By My00Z28 in forum General HelpReplies: 22Last Post: 07-14-2011, 11:01 AM -
knock sensor code with new knock sensors?
By zaaronz in forum General HelpReplies: 13Last Post: 02-27-2011, 06:26 AM -
Help: knock sensors
By bpopham22 in forum Firebird / WS6Replies: 11Last Post: 03-10-2010, 08:12 PM -
knock sensors
By David Ray in forum General HelpReplies: 2Last Post: 08-18-2009, 04:14 AM
Bookmarks