Results 1 to 7 of 7

Gauge and pod install....

This is a discussion on Gauge and pod install.... within the General Help forums, part of the LSx Technical Help Section category; The wiring is no problem for me. My problem....through the firewall. I haven't gone out and looked, but I need ...

  1. #1
    Slow'er'Ass Mr. Luos's Avatar
    Join Date
    Aug 2005
    Location
    Thornton, CO
    Posts
    23,785

    Red Tint Jewelcoat
    2008 Trailblazer SS

    Gauge and pod install....

    The wiring is no problem for me. My problem....through the firewall.

    I haven't gone out and looked, but I need a decent amount of wiring through to the engine bay. Do I need to drill, or is there some openings already there???
    2008 Trailblazer SS
    Yank PTB3600, Kooks 1 7/8" LT's, 4" intake, E-fans, Magnaflow, Sonnax kit, tranny cooler, tune.
    Lowered, HID's, tinted.

    1999 Pontiac Trans Am WS.6 #1747 SOLD
    531.1 RWHP 481.3 FT/Pounds all motor.

  2. #2
    Slow'er'Ass Mr. Luos's Avatar
    Join Date
    Aug 2005
    Location
    Thornton, CO
    Posts
    23,785

    Red Tint Jewelcoat
    2008 Trailblazer SS

    Anyone??

    I drilled the a-pillar pod today and got it ready to install. I just need the wiring through the firewall. Advice???

  3. #3
    Grand Imperial Wizard Sarge's Avatar
    Join Date
    Aug 2005
    Location
    Texas Department of Corrections
    Posts
    18,123
    Retired Outlaw Sum Bitch

    I cannot speak to your car specific but from the years and various models I have installed many guages on.....I drill a hole and put a rubber gromet in it....just have never found the perfect pre-drilled location yet

  4. #4
    Slow'er'Ass Mr. Luos's Avatar
    Join Date
    Aug 2005
    Location
    Thornton, CO
    Posts
    23,785

    Red Tint Jewelcoat
    2008 Trailblazer SS

    Crap.

    I just hate drilling.

  5. #5
    Grand Imperial Wizard Sarge's Avatar
    Join Date
    Aug 2005
    Location
    Texas Department of Corrections
    Posts
    18,123
    Retired Outlaw Sum Bitch

    Quote Originally Posted by Mr. Luos
    Crap.

    I just hate drilling.
    Bad dental experiance?

  6. #6
    Slow'er'Ass Mr. Luos's Avatar
    Join Date
    Aug 2005
    Location
    Thornton, CO
    Posts
    23,785

    Red Tint Jewelcoat
    2008 Trailblazer SS

    Something like that.

    I just can't see putting holes in the firewall for shit like this. Oh well....I will figure something out. I have plenty of time over the next two days.

  7. #7
    Beast
    Guest
    I have a triple pillar pod, and I routed all of my wires through a factory hole on the passenger side of the car. If you open the hood, and unbolt the computer up by the firewall(two 10mm bolts), and pull it out of its hole (no need to disconnect the wires, although I always go ahead and disconnect the battery just in case). Then you'll see a factory gromet you can use.

    Good luck!

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •