Results 1 to 5 of 5

egr block off plate

This is a discussion on egr block off plate within the General Help forums, part of the LSx Technical Help Section category; does anybody know what the dimensions are for the egr block off plate....i forgot my template and i need to ...

  1. #1
    Member redz284u's Avatar
    Join Date
    Aug 2005
    Location
    Littlerock, CA
    Age
    40
    Posts
    205

    Red
    1998 SS

    egr block off plate

    does anybody know what the dimensions are for the egr block off plate....i forgot my template and i need to make this part at work....i drove my car to work and dont wanna drive it back with out the plate....i think it will mess something up, it sounds nasty with out the plate.....
    98SS A4, TSP CLR LID, LS6 INTAKE, BMR SFC/STB/ LWR CNTRL & TRQ ARMS, KYB ADJ., HOTCHKINS SWAY BARS, MSD WIRES, JETHOT LT/ORY, MAGNAFLO CATBACK, EIBACH PROKIT, 19" TSW WHEELS, PERMA COOL TRANY COOLER.

    257.8 hp (MUSTANG-DYNO) b4 ANY MODS.
    13.6 1/4 mile

  2. #2
    Hemi Destroyer 98-LS1's Avatar
    Join Date
    Oct 2005
    Location
    Knoxvegas, Vol country Tennessee
    Posts
    1,112

    Sebring Silver
    98 Z-28 camaro

    I'll go and measure mine in a minute, I did the same thing as you! Took the EGR off at work and made some block off plates out of aluminum plate. I'll go out there and check, be right back.

  3. #3
    Hemi Destroyer 98-LS1's Avatar
    Join Date
    Oct 2005
    Location
    Knoxvegas, Vol country Tennessee
    Posts
    1,112

    Sebring Silver
    98 Z-28 camaro

    O.k., the intake block off plate measures:

    2-3/4 long with the holes drilled 2-1/4
    and a width of 1-1/2


    The header plate measures:

    1-1/2 wide by 2-1/2 long with the holes drilled
    2" apart.


    Hope this helps, BTW the holes are 7/16's on both plates

  4. #4
    Member redz284u's Avatar
    Join Date
    Aug 2005
    Location
    Littlerock, CA
    Age
    40
    Posts
    205

    Red
    1998 SS

    Quote Originally Posted by 98-LS1 View Post
    O.k., the intake block off plate measures:

    2-3/4 long with the holes drilled 2-1/4
    and a width of 1-1/2


    The header plate measures:

    1-1/2 wide by 2-1/2 long with the holes drilled
    2" apart.


    Hope this helps, BTW the holes are 7/16's on both plates
    awsome help, would u happen to know what it is for the egr one, passanger header, down below, by the alternator, and starter?????i think the dim's u gave me are for the air plugs, and the intake plug.....thanks alot for the help
    Last edited by redz284u; 07-24-2006 at 02:29 PM.

  5. #5
    Hemi Destroyer 98-LS1's Avatar
    Join Date
    Oct 2005
    Location
    Knoxvegas, Vol country Tennessee
    Posts
    1,112

    Sebring Silver
    98 Z-28 camaro

    All of my AIR stuff is still on the car, that plate is the forward most one in the front on the passenger side next to the a/c compressor. I only took off the EGR tube from the header to the intake manifold, I need to take that AIR crap off too but I will later. It's the right specs for a 98, I wouldn't do you wrong man! Hope this helps, if you need a pic of the plates I can snap one to show you exactly what I'm talking about. Your check engine light will come on after this stuff is removed so be sure to have it deleted out! Good luck

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •