Results 1 to 4 of 4

DMH Cutout for Borla Adjustable Install

This is a discussion on DMH Cutout for Borla Adjustable Install within the General Help forums, part of the LSx Technical Help Section category; Anyone done this before? I'm wondering how the wiring goes, and how and where to put the switch. Can someone ...

  1. #1
    Junior Member Tickwomp's Avatar
    Join Date
    Nov 2008
    Location
    Plano Texas
    Posts
    44

    NBM
    2000 Z28 M6 Vert

    DMH Cutout for Borla Adjustable Install

    Anyone done this before? I'm wondering how the wiring goes, and how and where to put the switch.

    Can someone help?

    TIA,

    Ken

  2. #2
    Member stephen02ws6's Avatar
    Join Date
    Jun 2007
    Location
    Dalzell, Illinois
    Age
    29
    Posts
    899

    red with black stripes
    2002 Trans Am WS6

    i put an electric cutout in for the plates. i ran the wire straight up through the spare tire area and then kept it tucked up in the trim all the way to the passenger seat. then i ran it under the seat to the center console and up to the tracton control panel. i hooked the power up the the cig lighter(instructions said not to but did) since the power and ground were right there. i put the switch in the panel by the traction switch and ran the LED on the side down by the floor. i didnt mount the LED i just slid it through the console where it meets the carpet a little just enough to see the light if i need to.

  3. #3
    Junior Member Tickwomp's Avatar
    Join Date
    Nov 2008
    Location
    Plano Texas
    Posts
    44

    NBM
    2000 Z28 M6 Vert

    Quote Originally Posted by stephen02ws6 View Post
    i put an electric cutout in for the plates. i ran the wire straight up through the spare tire area and then kept it tucked up in the trim all the way to the passenger seat. then i ran it under the seat to the center console and up to the tracton control panel. i hooked the power up the the cig lighter(instructions said not to but did) since the power and ground were right there. i put the switch in the panel by the traction switch and ran the LED on the side down by the floor. i didnt mount the LED i just slid it through the console where it meets the carpet a little just enough to see the light if i need to.
    Thanks for the quick input. Bases on your first hand experience, do you think it's possible to mount the switch in ashtray?

  4. #4
    Member stephen02ws6's Avatar
    Join Date
    Jun 2007
    Location
    Dalzell, Illinois
    Age
    29
    Posts
    899

    red with black stripes
    2002 Trans Am WS6

    i wanted to do that too. i think the switch was too big to fit. it has been a while since i did it. there was something with clearence issues though. maybe with yours being a manual it might have more room to fit. you could just play around with it before you run the wires to see where you can fit the switch and where you like it at.

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Similar Threads

  1. $500 Borla Adjustable, electric cutout for plates
    By Aetos in forum Parts For Sale / Trade
    Replies: 17
    Last Post: 08-02-2010, 08:37 PM
  2. Borla adjustable or non adjustable?
    By Ryanater in forum External Engine
    Replies: 20
    Last Post: 09-14-2007, 08:15 AM
  3. electronic Cutout on Adjustable Borla tips??
    By third_shift|studios in forum External Engine
    Replies: 15
    Last Post: 03-01-2007, 01:01 AM
  4. 98-02 Borla Adjustable Catback?
    By Mattg in forum Parts Wanted / Trade
    Replies: 0
    Last Post: 03-05-2006, 12:41 PM
  5. Borla Adjustable
    By bwinch in forum Parts For Sale / Trade
    Replies: 0
    Last Post: 02-08-2006, 08:14 PM

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •